Nokia PremiCell Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 66

Nokia PremiCell Скачать руководство пользователя страница 12

12

ã

2000 Nokia Mobile Phones. All Rights Reserved.

ATD> SIM2

Make a data call to the number stored

in the

SIM card memory location 2.

ATH Hang Up Call

This command normally hangs up the call. If the alternating call
data mode is currently active, ATH does not hang up the call but call
mode is switched from data to voice. If you want to disconnect the
alternating call, you must use the AT+CHUP command in-
stead.

Syntax:

ATH[<n>] Hang

up

call.

ATL Monitor Speaker Volume

This command has no effect on the data adapter. It is included for
compatibility rea-
sons.

Syntax:

ATL[<n>]

ATM Monitor Speaker Mode

This command has no effect on the data adapter. It is included for
compatibility rea-
sons.

Syntax:

ATM[<n>]

ATO Go On-Line

This command is used when you have made a connection with the
remote device and have escaped (with the +++ command) to the
command mode. Give the command to return from the (on-line)
command mode to normal on-line opera-
tion.

Syntax:

ATO[<n>] Go to on-line state. Response is CONNECT [<speed>].

«
...
10
11
12
13
14
...
»

Содержание PremiCell



































































Отзывы:

Нет отзывов