Nokia 6090 Скачать руководство пользователя | Manualshive

Страница: 70 / 84

background image

Nokia 6090 AT Command Set

68

Copyright © 2001. Nokia Mobile Phones. All rights reserved.

Error Values

Below are the set of error cases supported by the Nokia 6090.

+CME ERROR Values

The following table indicates which AT commands can return a numeric

<err> value

.

The table has three columns. GSM defined error numbers are listed in column 2.
These are translated by the Nokia 6090 to a Nokia specific error number as shown in
column 3. The error code displayed in column 3 is that sent to the TA. See table
"Kinds of Errors" for column 3 error descriptions.

AT Command

+CME <err> Value Kinds of Errors

D><str>

3

9

5

1

10

2

11

3

12

4

22

7

23

8

D>mem<n>

3

9

5

1

10

2

11

3

12

4

21

5, 6

23

8

D><n>

3

9

5

1

10

2

11

3

12

4

21

5, 6

23

8

«
...
68
69
70
71
72
...
»

Содержание 6090





















































































Отзывы:

Нет отзывов

Похожие инструкции для 6090

Бренд: Hama Страницы: 6

Бренд: LAS Страницы: 44

Бренд: LAS Страницы: 24

Бренд: Mobis Страницы: 16

Бренд: Subaru Страницы: 216

Бренд: Tapco Страницы: 16

Бренд: Prorack Страницы: 14

Бренд: EUFAB Страницы: 12

2016 Sandero Stepway

Бренд: Renault Страницы: 183

Бренд: BMW Страницы: 55

Бренд: Whispbar Страницы: 15

Бренд: Draw tite Страницы: 4

Бренд: EFILive Страницы: 25

PRIME DESIGN VRR3-FT21G-ST

Бренд: Safe Fleet Страницы: 12

2013 2500 Big Horn

Бренд: RAM Страницы: 12

Бренд: Curt Manufacturing Страницы: 4

Бренд: Whispbar Страницы: 112

Бренд: TracRac Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды