manualshive.com logo in svg

NIVELCO UNICONT PMG-500, Руководство пользователя и программирования, Страница: 8 / 41

Поделиться
Скачать
NIVELCO UNICONT PMG-500 Скачать руководство пользователя страница 8

8 pmg511en21p01

1. Measured Value (PV):

 

RUN mode: it shows the currently measured value 

(PV)

. 

Setting mode: it shows the name of the parameter.

2. Set value (SV):

 

RUN mode: it shows the set value 

(SV)

. 

Setting mode: it shows the the parameter value.

3. Unit (°C / °F / %) indicator:

 It displays the unit set in parameter group 3. The unit applies to the displayed 

values of the 

PV 

and SV. 

4. Manual control indicator (MAN):

 it switches on during manual control.

5. Multi SV indicator (SV1, SV2, SV3) LEDs:

 Indicates the different target value setting currently in use 

 

(SV1-3)

. The base destination field 

(SV0)

 is valid if none is active. Not available for all models.

6. Auto-tuning indicator (AT):

 flashes every 1 second when auto-tuning is executed.

7. Alarm output (AL1) indicator:

 it turns on when the alarm output is on.

8. Control output (OUT1, OUT2) indicator

: it turns on when the corresponding control output is active. During 

manual control, it switches off if the measured value is 0.0% when using a current output; otherwise, it is 

switched on continuously. During automatic control, it switches on when the measured value exceeds 3.0% 

and switches off when it falls below 2.0%.

9.  

 button:

 It is used when entering parameter group, returning to RUN mode, moving parameter, saving 

the set value 

 

Functions:

9.1

 Press and hold the 

 

button for longer than 2 seconds in RUN mode to enter Setting mode.

9.2

 Press and hold the 

 button for 1.5 seconds to enter another parameter group in Setting mode.

9.3

 Press and hold the 

 

button for longer than 3 seconds in to return to RUN mode from Setting mode.

9.4

 Press and hold the 

 

button at the last parameter name of any parameter group, and the device 

returns to the current main parameter group, where other parameter groups can be accessed.

9.5 

If no button is pressed within 30 seconds in setting mode, the device will automatically return to RUN 

mode, and the previously saved setting value will be retained.

10. 

 

buttons: they are used when entering the set value, changing mode, navigating between 

parameters/values, and changing values up/down.

11.

 Digital input key: When pressing the

 

 buttons together for 3 seconds, it operates the  

RUN/STOP, alarm clear, and auto tuning functions.

Содержание UNICONT PMG-500










































Отзывы:

Нет отзывов