background image

10

5-4. Mounting/Removing Cutter

WARNING

  Do not use any other combinations of Pilot 

Pin  and  cutter  than  those  shown  in  the 

compatibility table.

  Wear safety gloves when replacing cutter.

(1)  Bring the Drill Motor up by turning the Rod Handle 

clockwise. (Fig. 10)

     

Fig. 10

(2)    Insert  a  Pilot  Pin, 

appropriate for the cutter 

size,  into  the  cutter. 

(Fig.11)

(3)  Align the depression in 

the cutter with the white 

line on the Sleeve, and 

then insert the cutter.

 

When  you  insert  the 

c u t t e r   f a r   e n o u g h 

the  Sleeve  will  turn 

clockwise and lock with 

a clicking sound..

 

*   W h e n   y o u   f i n d   i t 

h a r d   t o   i n s e r t   t h e 

cutter, turn the Sleeve 

counterclockwise and do 

over. (Fig.12)

(4)  To remove the cutter, 

t u r n   t h e   S l e e v e 

counterclockwise.  

 

The cutter will come off. 

(Fig.13)

5-5. Preparation of Cutting Oil

Cutting Oil Safety Precautions

WARNING

(1) Use

 Use Cutting Oil for cutting purpose only.  Do not use 

it for household purposes

(2) Handling Precautions 

 The Cutting Oil contains amine.  Do not mix it up 

with rust inhibitor, etc. containing nitrite.

 Wear  safety  glasses  for  eye  protection  when 

handling Cutting Oil: eye injury may results if it gets 

into your eyes. 

 Wear protective gloves for hand protection when 

handling Cutting Oil: skin injury may result if it 

comes into contact with your skin. 

 Wear  respirator  when  exposure  to  respiratory 

hazards  with  oil  mist  or  vapor  is  anticipated.  

Inhalation of oil mist or vapor may make you feel 

sick. 

 When diluting Cutting Oil, follow the instructions per 

the Operation Manual.

 Keep Cutting Oil out of reach of children.

 Do not drink Cutting Oil.

(3) First Aid

 If Cutting Oil gets into your eyes, immediately open 

your eyelids with your fingers and wash your eyes 

with plenty of water for at least 15 minutes.  If your 

eyes feel irritated, consult with a medical doctor and 

follow his/her instructions.

 If Cutting Oil comes into contact with your skin, 

immediately wash it away with plenty of water and 

soap.  Take off contaminated clothes.  Clean the 

clothes if you need to wear it again.  If your skin 

feels irritated, consult with a medical doctor for 

medical instructions.

 If someone inhales oil mist or vapor, immediately 

take him/her to an area where fresh air is abundant 

and wrap up his/her body with a blanket, etc. to 

keep  body  temperature.    Have  him/her  take  a 

rest and consult with a medical doctor for medical 

instructions.

 If someone drinks Cutting Oil, immediately make 

him/her drink plenty of water and vomit it.  Consult 

with a medical doctor for medical instructions.  When 

unconscious, do not pour water into his/her mouth 

nor induce him/her to vomit.

(4) Instructions in Case of Fire

 If 

fire

 breaks out in the vicinity, wear PPE (personal 

protective equipment) and use foam, powder or 

CO

2

 fire extinguisher to put the fire out from the 

windward.

Rod Handle

Downward

Upward

Pull down out of the body

Fig. 11

Fig. 12

Fig. 13

Pilot pin

Cutter

Spindle Arbor

Turn the Sleeve

to the left

Spindle Arbor

Pull out

Sleeve

White line

Depression

Align

Sleeve

Содержание ATRA ACE WA-3500





















Отзывы: