background image

9

4.   FUNCTIONS OF ELECTRONIC 

CONTROL

4-1. Overload Detecting Function

When overload occurs during drilling operation, 

the overload detector puts the following functions 

to work. Please note, however, that there may be 

cases where the overload detector does not work 

properly if power is drawn from an engine generator 

with fluctuating output voltage, sometime tool high 

and sometime too low.  

 Automatic Feed Rate Control Function

Automatic drill feed starts slowly for the first few 

seconds and then it picks up speed automatically to 

an appropriate level in terms of cutting load applied 

to the cutter. In addition, a cutter diameter factor 

is also taken into account for automatic feed rate 

control.  

 Automatic Stop Function

Overload  to  the  Drill  Motor  or  feed  motor 

automatically stops the drill and ongoing feed, 

preventing possible damage to the machine and 

cutter. However, if a worn or blunt cutter is being 

used, it may break. 

4-2. Automatic Cycle Stop Function

When drilling operation is complete with the machine 

relieved  of  cutting  load,  the  Drill  Motor  stops 

automatically.

4-3. Limit Switch Function

Even if the automatic cycle stop function fails to 

operate and the drill continues to feed down, the 

Limit Switch will stop the down-feed near the lower 

limit of the stroke and the Drill Motor.

4-4. Lateral-Shifting Detection Function

This function stops drill feed and the Drill Motor 

when lateral shifting of the Magnet is detected.

4-5. Re-Start Prevention Function

The re-start prevention function comes into play 

when power failure is restored that has occurred 

during operation. 

Thanks to this feature, when a plug that has been 

disconnected during operation is re-plugged into the 

receptacle or when power failure is restored that has 

occurred during operation, the Drill Motor will NOT 

restart automatically preventing possible accident -- 

although Magnet lamp will come on and magnetic 

power restored. 

To resume operation, turn ON the Motor Switch on 

the side of the machine to start the Drill Motor.

4-6. Magnet Interlocking Function

When the Magnet fails the Drill Motor will not start 

revolving. To repair defective Magnet, please contact 

sales agent through which you have purchased your 

machine or an authorized dealer near you.

5.  MACHINE SETUP

WARNING

  When setting up machine, turn off the Magnet 

Switch and disconnect the power supply plug 

from power source.

5-1. Mounting Parts 

Mount the Side Handle on the Drill Motor.

5-2. Using Cutter

CAUTION

● 

Use One-Touch type cutters only. 

●  

For better workability and safety, do not use 

worn or damaged cutters.

5-3. Combination of Cutter and Pilot Pin 

CAUTION

●  

Do not use any other combinations than those 

shown in the compatibility table.

Use a Pilot Pin appropriate for the cutter. (Fig.9)

A Pilot Pin to be used varies depending on the cutter 

type, diameter, length (depth).  A wrong combination 

of  cutter and Pilot Pin would not allow slug  to be 

ejected at the end of drilling and/or prevent Cutting 

Oil from  reaching the cutting point, resulting in 

cutting tool damage.

06025

   PN:TK01167

08025

   PN:TJ12696

06050

   PN:TK01166

0850

   PN:TK00802

HBO 14 - 17 dia.

Depth 25 mm

HBO 17.5 - 35 dia.

Depth 25 mm

HBO 14 - 18 dia.

Depth 50 mm

JBO 17.5 - 35 dia.

Depth 35 mm

JBO 17.5 - 35 dia.

Depth 50 mm

JBO 17.5 - 35 dia.

Depth 75 mm

HBO 19 - 35 dia.

Depth 50 mm

PILOT PIN

HI-BROACH Cutters

PILOT PIN

JETBROACH Cutters

08050

   PN:TJ16019

08035

   PN:TJ15859

08050

   PN:TJ16019

08075

   PN:TJ17436

6.35 dia.

6.35 dia.

8 dia.

100 mm

7 dia.

112 mm

8 dia.

91 mm

8 dia.

112 mm

8 dia.

5 dia.

8 dia.

81 mm

76 mm

5 dia.

112 mm

133 mm

8 dia.

Fig. 9

Содержание ATRA ACE WA-3500





















Отзывы: