manualshive.com logo in svg

Nippon Primex NP-F369, Технические характеристики

Поделиться
Скачать
Nippon Primex NP-F369 Скачать руководство пользователя страница 24

D-F10120 NP-F369 Product Spec Rev.0.01(Provisional Ver.) 

17

 
3.

   

Configurations 

 

3.1

 

Interface

【

USB(V2.0 FULL SPEED)

】

 

 

1) Version 

    ：

V2.0 FULL SPEED (12Mbps) 

 

2) Port

 

 

    ：

Upstream port (B jack) 

 

3) Power Supply 

    ：

Self Powered 

 

4)  Reset Function: Printer is reset automatically when connecting USB cable connected to the 

host.  

 
*When using with USB interface, make sure to use driver

*NOTE1

 we provide. 

When direct transfer, make sure to monitor receive buffer remaining amount

*NOTE2

 and DO NOT transmit 

data exceeding this amount. 
 

*NOTE1

 :  Use either one of the following drivers or newer version. 

NPI EX Driver Ver.*.*.*.* 
NPI Printer_DS2.0 

 

*NOTE2

 :  Receive buffer remaining amount's auto-reply format (when MS2-7 : OFF) 

 

[FF]h + [01]h + [00]h + [00]h + [00]h + n 

*[00 

≤

 n 

≤

 0F]h 

     

  n = Receive buffer remaining amount (0 ~ 15K byte) 

Содержание NP-F369











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды