WSS100 - WST100
09/2014
8
GB
Cleaning the containers
WARNING!
Before proceeding with these operations, turn off the
vacuum cleaner and remove the plug from the power
socket.
Shaving container (optional)
■ Clean the container after each emptying (see “Emptying
the shaving container” paragraph).
■ Check that the holes are free of dirt; clean them if
necessary.
Liquid container
Figure 9
1
Float and relative support
2
Shaving container (optional)
3
Container closing band
4
Liquid exhaust valve
■ Empty the liquid container (see “Emptying the containers”
paragraph).
■ Open the liquid container closing band (
3
).
■ Lift the motor head.
■ Remove the float and its support (
1
) or the shaving
container (
2
) (optional).
■ Wash the container with water to remove deposits.
■ Open the exhaust valve (
4
) to empty the container.
■ Close the exhaust valve (
4
).
■ Place the float and its support or the shaving container (if
applicable) back into position.
N.B. Make sure the float support is correctly
positioned (fig. 9).
■ Lock the motor head by using the liquid container closing
band (
3
).
Cleaning or replacement of the vapour
filters
Figure 10
1
Filters
2
Baffle plate
3
Filter box
■ Remove the safety screw (
4
) and open the motor head
clamp (
5
).
■ Lift the motor head.
■ Remove the filter box (
3
) by unscrewing the fixing
screws.
■ Remove the filters (
1
) and the baffle plate (
2
), then clean
the filters with water or replace them if necessary.
■ Reinstall the filters (
1
) and the baffle plate (
2
) making
sure they are correctly positioned.
■ Install the filter box and secure it by screwing the fixing
screws.
■ Reinstall the motor head and close the container with the
appropriate closing band, then put the safety screw in
place (
4
).
Tightness inspection
Figure 11
1
Vacuum hose
2
Liquid level indicator tube
■ Hoses check
Make sure that the suction connecting hose (
1
) and the
level hose (
2
) are in a good condition and correctly fixed.
If the hose is damaged, broken or badly connected to the
unions, it must be replaced.
Figure 12
1
Gasket
2
Liquid container
3
Motor head
■ Motor head tightness check
Replace the seal (
1
) between the container (
2
) and the
motor head (
3
) if it is torn, cut, etc.
Содержание CFM WSS 100
