Nilfisk-Advance BA 750C, Инструкция по эксплуатации

Страница: 18 / 72

18 18
18 18 18 - FORM NO. 56041519 - CMAX ™ 28ST, 34ST / I-MAX 28C, 32C / BA 750ST, 750C / BA 850ST
FUNCTIONAL DESCRIPTION OF CONTROLS: FUNCTIONAL DESCRIPTION OF CONTROLS:
FUNCTIONAL DESCRIPTION OF CONTROLS: FUNCTIONAL DESCRIPTION OF CONTROLS: FUNCTIONAL DESCRIPTION OF CONTROLS:
Solution Tank Fill Solution Tank Fill
Solution Tank Fill Solution Tank Fill
Solution Tank Fill (1) (1)
(1) (1)
(1) – Open to fill the solution tank, use non-foaming chemicals only.
Recovery Tank Cover Recovery Tank Cover Recovery Tank Cover Recovery Tank Cover Recovery Tank Cover (2) (2) (2) (2) (2) – Point of entry for waste water into tank. Also houses float ball which shuts off vacuum port to vac motor when tank
is full.
Drive Paddle
Drive Paddle Drive Paddle Drive Paddle Drive Paddle (3) (3) (3) (3) (3) – Located on top at the rear of the machine, the operator can make the machine go forward by pushing forward on it, or reverse
by pulling backward on it. The speed is variable depending on how far forward or backward the paddle is moved. When the brush head is in the
“DOWN” position, the brushes and solution will operate when the drive is engaged in either direction, but will stop after the machine is stationary
for 3 seconds.
Solution Drain Hose / Level Indicator
Solution Drain Hose / Level Indicator
Solution Drain Hose / Level Indicator Solution Drain Hose / Level Indicator Solution Drain Hose / Level Indicator (4)
(4)
(4) (4) (4) – Used to empty the solution tank and show current level of solution in tank, graduations are marked
on the side of the solution tank next to the hose.
Recovery Drain Hose
Recovery Drain Hose Recovery Drain Hose Recovery Drain Hose Recovery Drain Hose (5) (5) (5) (5) (5) – Used to empty the recovery tank.
Squeegee Adjustment Bolt Squeegee Adjustment Bolt
Squeegee Adjustment Bolt Squeegee Adjustment Bolt Squeegee Adjustment Bolt (6)
(6)
(6) (6) (6) – Used to adjust the tilt of the squeegee. Turn bolt clockwise to tilt the squeegee backwards and counter-clockwise
to tilt it forward.
Squeegee Blade Latch
Squeegee Blade Latch Squeegee Blade Latch Squeegee Blade Latch Squeegee Blade Latch (7) (7) (7) (7) (7) – Holds rear squeegee blade and straps in place, release to replace rear blade.
Squeegee Squeegee Squeegee Squeegee Squeegee (8) (8) (8) (8) (8) – Picks up solution after scrubbing.
Machine Battery Connector Machine Battery Connector Machine Battery Connector Machine Battery Connector Machine Battery Connector (9) (9) (9) (9) (9) – Batteries plug into this connector, disconnect to charge batteries.
Solution Flow Control Knob Solution Flow Control Knob
Solution Flow Control Knob Solution Flow Control Knob
Solution Flow Control Knob (10) (10)
(10) (10)
(10) – Turn this dial to the right to decrease solution flow to the floor. Turn to the left, to increase the amount of solution
flow to the floor. When the Drive Paddle (3) (3) (3) (3) (3) is released from either forward or reverse travel, the solution flow will stop automatically, and resume
when the drive is engaged.
Speed Limit Control Knob
Speed Limit Control Knob
Speed Limit Control Knob Speed Limit Control Knob
Speed Limit Control Knob (11) (11)
(11) (11)
(11) – The Speed Limit Control Knob is used to adjust the maximum speed in both forward or reverse.
Wheel Drive Circuit Breaker Wheel Drive Circuit Breaker Wheel Drive Circuit Breaker Wheel Drive Circuit Breaker Wheel Drive Circuit Breaker (12) (12) (12) (12) (12) – Provides overload protection to machine’s wheel drive motor. If it trips, it will pop out. To reset, wait one minute
and press the button back in. If any breaker trips repeatedly, have the machine serviced.
Control Circuit Circuit Breaker
Control Circuit Circuit Breaker Control Circuit Circuit Breaker Control Circuit Circuit Breaker Control Circuit Circuit Breaker (13) (13) (13) (13) (13) – Provides overload protection. If it trips, it will pop out. To reset, wait one minute and press the button back
in. If any breaker trips repeatedly, have the machine serviced.
Brush Deck
Brush Deck
Brush Deck Brush Deck
Brush Deck (14) (14)
(14) (14)
(14) – Contains brush drive motors and brushes.
Operator Control Handle Operator Control Handle Operator Control Handle Operator Control Handle Operator Control Handle (15) (15) (15) (15) (15) – Operator holds onto this to control the machine.
Operator Hand Brake (optional) (16) Operator Hand Brake (optional) (16)
Operator Hand Brake (optional) (16) Operator Hand Brake (optional) (16) Operator Hand Brake (optional) (16) – Use to prevent machine from rolling.
Squeegee Lever (17)
Squeegee Lever (17) Squeegee Lever (17) Squeegee Lever (17) Squeegee Lever (17) – This lever is used to lower or raise the squeegee assembly.
Solution Filter (18)
Solution Filter (18) Solution Filter (18) Solution Filter (18) Solution Filter (18) – Filters solution prior to dispensing on floor.
Hopper (19)
Hopper (19)
Hopper (19) Hopper (19) Hopper (19) – Found only on cylindrical models, catches debris.
Idler Assembly (20)
Idler Assembly (20) Idler Assembly (20) Idler Assembly (20) Idler Assembly (20) – Found only on cylindrical models, remove this to access broom on each side.