Nilfisk-Advance AquaRide BRX 700, Руководство по обслуживанию, Страница: 75 / 82

FORM NO. 56043089 / AquaRide ™ / BRX 700 - 73 73 73 73 73
ELECTRICAL SYSTEM ELECTRICAL SYSTEM ELECTRICAL SYSTEM ELECTRICAL SYSTEM ELECTRICAL SYSTEM
Turning Fault Detection On or Off: Turning Fault Detection On or Off:
Turning Fault Detection On or Off: Turning Fault Detection On or Off: Turning Fault Detection On or Off:
FACTORY DEFAULT: ON
Normally, the main control unit will perform checks of the electrical system during operation. If a fault occurs in a particular system
that system (and possibly others) will be shut down. This can make troubleshooting the system difficult. This option will allow service
personnel to disable some of the fault detection checks to facilitate troubleshooting. This will
not disable the over-current protection
on any of the systems. To turn the fault checking on or off:
1 Turn the main power key switch main power key switch main power key switch main power key switch main power key switch to the off off off off off position.
2 Press and hold the scrub system off switch scrub system off switch scrub system off switch scrub system off switch scrub system off switch and the solution switch solution switch solution switch solution switch solution switch.
3 While holding both switches turn the main power key switch main power key switch main power key switch main power key switch main power key switch to the on on on on on position.
4 Continue to hold both switches until the solution indicator is yellow.
5 Release both switches. The status display will now indicate “E” or “d”.
6 Pressing and releasing the solution solution solution solution solution switch will now select between “E” for enabled or “d” for disabled. Enabled means that
the fault checking is turned on, disabled means that the fault checking is turned off.
7 To save the new setting turn the main power key switch main power key switch main power key switch main power key switch main power key switch to the off off off off off position.
8 The new setting will be saved and will remain in effect until it is changed again.
Turning the High Speed Scrub Option On or Off: Turning the High Speed Scrub Option On or Off:
Turning the High Speed Scrub Option On or Off: Turning the High Speed Scrub Option On or Off:
Turning the High Speed Scrub Option On or Off:
FACTORY DEFAULT: ON
The control system on the AquaRide is programmed to limit the maximum speed while scrubbing to a value less than that allowed
for driving when not scrubbing. The speed select switch on the control panel will override this speed limit feature and allow
scrubbing at a higher rate of speed. If it is desired to prevent scrubbing at this faster speed the fast/slow feature can be turned off.
To turn this feature on or off perform the following steps:
1 Turn the main power key switch
main power key switch
main power key switch main power key switch main power key switch to the off
off
off off off position.
2 Press and hold the fast/slow switch
fast/slow switch
fast/slow switch fast/slow switch fast/slow switch.
3 While holding the fast/slow switch turn the main power key switch main power key switch main power key switch main power key switch main power key switch to the on on on on on position.
4 Continue to hold the fast/slow switch until the fast/slow indicator is green.
5 Release the fast/slow switch. The status display will now indicate “E” or “d”
6 Pressing and releasing the fast/slow fast/slow fast/slow fast/slow fast/slow switch will now select between “E” for enabled or “d” for disabled. Enabled means that
the high speed scrub feature is turned on, disabled means that the high speed scrub feature is turned off.
7 To save the new setting, turn the main power key switch main power key switch main power key switch main power key switch main power key switch to the off off off off off position.
8 The new setting will be saved and will remain in effect until it is changed again.
Scrub Deck Motor Type Selection: Scrub Deck Motor Type Selection: Scrub Deck Motor Type Selection: Scrub Deck Motor Type Selection: Scrub Deck Motor Type Selection:
FACTORY DEFAULT: MODE = E (EXTRACTOR), MOTOR TYPE: 1 IF EXTRACT ONLY DECK, 2 IF SWEEP EXTRACT DECK.
The AquaRide can be equipped with two different scrub deck options. This function configures the control unit current settings for
each of the scrub deck types. Improper setting of the motor type may result in motor damage due to overloading.
Improper setting of the motor type may result in motor damage due to overloading. Improper setting of the motor type may result in motor damage due to overloading. Improper setting of the motor type may result in motor damage due to overloading. Improper setting of the motor type may result in motor damage due to overloading. To select
the proper scrub deck motor type:
1 Turn the main power key switch main power key switch
main power key switch main power key switch
main power key switch to the off off
off off
off position.
2 Press and hold the scrub system off scrub system off
scrub system off scrub system off
scrub system off and restore mode switches restore mode switches
restore mode switches restore mode switches
restore mode switches.
3 While holding both switches turn the main power key switch main power key switch
main power key switch main power key switch
main power key switch to the on on
on on
on position.
4 Continue to hold both switches until the restore mode indicator is yellow.
5 Release both switches. The status display will now indicate “S” or “E”.
6 Pressing and releasing the restore mode switch
restore mode switch
restore mode switch restore mode switch restore mode switch will now select between “S” for scrubber and “E” for extractor. Make sure
Make sure
Make sure Make sure Make sure
that “E” is displayed that “E” is displayed that “E” is displayed that “E” is displayed that “E” is displayed.
7 Press the scrub system off scrub system off scrub system off scrub system off scrub system off switch switch switch switch switch to save this setting
8 The status display will now display “1”, or “2”. Pressing the restore mode restore mode restore mode restore mode restore mode switch switch switch switch switch will now select between the two settings.
Select “1” if the machine is equipped with an extract-only deck. Select “2” if the machine is equipped with a sweep-extract deck.
9 Once the proper setting is displayed, press the scrub system off scrub system off scrub system off scrub system off scrub system off switch switch switch switch switch to save this setting.
10 The status display will now display “d” to indicate that the operation is done.
11 Turn the main power key switch
main power key switch main power key switch main power key switch main power key switch to the off off off off off position.
SPECIAL PROGRAM OPTIONS (CONTINUED) SPECIAL PROGRAM OPTIONS (CONTINUED)
SPECIAL PROGRAM OPTIONS (CONTINUED) SPECIAL PROGRAM OPTIONS (CONTINUED)
SPECIAL PROGRAM OPTIONS (CONTINUED)