Nilfisk-Advance AquaRide BRX 700 Скачать руководство пользователя страница 13

Страница: 13 / 82

FORM NO. 56043089 / AquaRide

™

/ BRX 700 - 11

KNOW YOUR MACHINE DESCRIPTIONS:

Recovery Tank Cover

Recovery Tank Cover (((((1

11))))) – Open to access Recovery Bladder for rinsing and/or cleaning Float Cage.

Solution Tank Fill

Solution Tank Fill Cover

Cover

Cover (((((2

22))))) – Open to fill the solution tank, only use low-sudsing liquid detergents designed for carpet extraction.

The area around the recovery bladder inside the recovery tank also holds solution. Total capacity is 40 gallons (151 Liters).
Operator’s Seat

Operator’s Seat

Operator’s Seat (((((3

33))))) – The machine operator sits here. The seat has a safety switch which prevents the machine from moving without

an operator in the seat.
Solution Tank Drain Hose

Solution Tank Drain Hose

Solution Tank Drain Hose (((((4

44))))) – Used to empty the solution tank.

Steering Wheel Tilt Adjust Knob

Steering Wheel Tilt Adjust Knob (((((5

55))))) – Push down on this knob to adjust the Steering Wheel up or down.

Brake Pedal / Parking Brake

Brake Pedal / Parking Brake (((((6

66))))) – Push down to stop machine. NEVER leave machine unattended without setting Parking Brake.

Solution Spray Jets

Solution Spray Jets (((((7

77))))) – Based upon which extraction mode is selected (maintenance or restoration) the solution will be sprayed

out one of the two different jets.
Drive Pedal, Directional / Speed

Drive Pedal, Directional / Speed

Drive Pedal, Directional / Speed (((((8

88))))) – The operator can make the machine go forward by pushing forward on it, or reverse by pulling

backward on it. The speed is variable depending on how far forward or backward the pedal is moved.
Vacuum Shoes (

Vacuum Shoes (

Vacuum Shoes (9

99))))) – Removes excess solution from carpet after cleaning.

Drive and Steer Wheel

Drive and Steer Wheel (((((10

10))))) – Wheel drive motor attached to this wheel to propel machine either forward or reverse. Also attached

to Steering Wheel for steering left or right.
Wheel Drive Circuit Breaker

Wheel Drive Circuit Breaker

Wheel Drive Circuit Breaker (((((11

11))))) – Provides overload protection to machine’s wheel drive motor, 45 Amp. If it trips, it will pop out.

To reset, wait one minute and press the button back in. If any breaker trips repeatedly, have the machine serviced.
Control Circuit Circuit Breaker

Control Circuit Circuit Breaker

Control Circuit Circuit Breaker (((((12

12))))) – Provides overload protection, 10 Amp. If it trips, it will pop out. To reset, wait one minute and

press the button back in. If any breaker trips repeatedly, have the machine serviced.
Emergency Stop / Battery Disconnect

Emergency Stop / Battery Disconnect

Emergency Stop / Battery Disconnect (((((13

13))))) – Push in on lever to disconnect batteries.

Brush deck

Brush deck (((((14

14))))) – Contains brush drive motor(s), brush(s) and solution spray jets.

Rear Wheel

Rear Wheel (((((15

15))))) – These two wheels along with the drive wheel, support the machine. Power and steering are supplied through

the front drive wheel.
Battery Compartment

Battery Compartment

Battery Compartment (((((16

16))))) – Batteries stored here, flip seat panel up to access.

Recovery Bladder Shutoff Float

Recovery Bladder Shutoff Float (((((17

17))))) – Shuts off vacuum when recovery bladder is full.

Vacuum Motors’ Filter Housing

Vacuum Motors’ Filter Housing (((((18

18))))) – Location of Vacuum Motors air intake filters.

Waste Water Bladder

Waste Water Bladder (((((19

19))))) – Contains waste water as it is recovered from carpet.

Total capacity of XX gallons (XX Liters).

Solution Filter (

Solution Filter (20

20))))) – Filters solution prior to entering pump and being sprayed on floor.

Recovery Drain Hose

Recovery Drain Hose (((((21

21))))) – Used to empty the recovery bladder.

Machine Battery Connector

Machine Battery Connector (((((22

22))))) – Batteries plug into this connector, disconnect to charge batteries.

Control Panel

Control Panel (((((23

23))))) – Operator Controls found here, see “FUNCTIONAL DESCRIPTION OF CONTROL SWITCHES”.

Debris Hopper (on sweeper models only) (

Debris Hopper (on sweeper models only) (24

24))))) – Collects debris that has been swept up by the machine. Empty and clean daily.

Solution Control Valve (

Solution Control Valve (25

25))))) – This valve should be fully open whenever extracting. Only close this valve before removing the solution

filter to prevent loss of solution.

KNOW YOUR MACHINE

Содержание AquaRide BRX 700



















































































Результаты поиска

Содержание AquaRide BRX 700

Отзывы:

Nilfisk-Advance AquaRide BRX 700, Руководство по обслуживанию, Страница: 13 / 82

Результаты поиска

Содержание AquaRide BRX 700

Отзывы: