background image

10

I

N T E L L I G E N T

P

O W E R

C

O N T R O L L E R

POWER CORD

Plugs directly into the

wall AC outlet.

SWITCHED 120 VOLT AC POWER OUTLETS

These turn on and off according to the way you

have programmed your IPC-6.

REMEMBER: THE TOTAL POWER CONSUMPTION OF ALL DEVICES
PLUGGED INTO THE IPC-6 MAY NOT EXCEED 1500 WATTS.

9

I

N T E L L I G E N T

P

O W E R

C

O N T R O L L E R

ACCUSENSE

TM

120 VOLT AC POWER OUTLETS

Turning on the device plugged into one of these outlets will trigger the cor-

responding (A or B) ON sequence. Turning off the device plugged into one

of these outlets will trigger the corresponding (A or B) OFF sequence.

CONTROLLED 12 VOLT DC OUTPUTS
Positive = Terminal 1  Ground = Terminal 2

SENSING 3-30V

AC or DC INPUTS

Contact groups provide you with a NORMALLY OPEN (N.O.) contact that closes,
or a NORMALLY CLOSED (N.C.) contact that opens when C1 or C2 are activat-
ed.

N.O. = Terminal 1, COMMON = Terminal 2, N.C. = Terminal 3

CONTACT

GROUP

ONE

CONTACT

GROUP

TWO

N
O

C
O

M

N
C

3-30V

AC/DC

SWITCHED OUTLETS

A

RELAY

DC OUT

RELAY

DC OUT

TRIGGER

INPUTS

CONTROL OUTPUTS

1

2

3

4

5

6

12V

0.1 AMP

-

+

N
O

C
O

M

N
C

12V

0.1 AMP

+

-

+

-

+

Niles Audio

Corporation, Inc.
Miami, Florida  USA

NILES

120 Volts AC  60 Hz.

1500 Watts Max.

CONTROL
OUTPUT
RELAYS
C1 and
C2 rated
at 5 Amps,
30 Volts
Max., AC
or DC.

C1

C2

CURRENT SENSE OUTLETS

B

A

B

3-30V

AC/DC

-

Содержание IPC-6











Отзывы: