Nikon Total Station DTM-322 Скачать руководство пользователя страница 22

Страница: 22 / 185

Preparation

Total Station DTM-322 Instruction Manual

Unpacking and Packing the Instrument

Note –

Handle the DTM-322 instrument gently to protect it from shocks and excessive

vibration.

Unpacking

To unpack the instrument, grip the carrying handle
and gently remove the instrument from the carrying
case.

Packing

Note –

Store the instrument with the battery case

attached.

To pack the instrument back into the carrying case:

Set the telescope in the horizontal face-1 position.

Align the

storage mark on the bottom of

the face-1 keyboard with the

mark on the

leveling base clamp knob.

Lightly fasten the clamp knobs.

Place the instrument in the carrying case.

Charging the Battery

Before charging the battery, read the warnings (also listed in the Safety section at the
front of this manual) and the following notes.

WARNING –

To charge the battery, use only the battery charger that is supplied with the

instrument. Do NOT use any other charger or you may cause the battery to catch fire or
rupture.

WARNING –

Do not cover the battery charger while the battery is being recharged. The

charger must be able to dissipate heat adequately. Coverings such as blankets or clothing can
cause the charger to overheat.

WARNING –

Avoid recharging the battery in humid or dusty places, in direct sunlight, or near

heat sources. Do not recharge the battery when it is wet. If you do, you may receive electric
shocks or burns, or the battery may overheat or catch fire.

WARNING –

You should take care not to short circuit the contacts. Short circuits can cause the

battery to catch fire or burn you.

Содержание Total Station DTM-322


























































































































































































Результаты поиска

Содержание Total Station DTM-322

Отзывы:

Похожие инструкции для Total Station DTM-322

Бренды по названию

Популярные бренды

Nikon Total Station DTM-322, Инструкция по эксплуатации

Результаты поиска

Содержание Total Station DTM-322

Отзывы:

Похожие инструкции для Total Station DTM-322

Бренды по названию

Популярные бренды