Nidec Leroy-Somer D510 C Скачать руководство пользователя страница 36

Страница: 36 / 64

2019.02 / p

Electric Power Generation

Installation and maintenance

D510 C

Digital voltage regulator

4243 en -

- [Expert mode] Start on Threshold

Activate and set this function. This function

allows an initialisation of the voltage

regulation in a way which avoids the voltage

overshoots during voltage build up. The

PMW % level reduce the excitation current

up the voltage threshold voltage level. The

Start on threshold can be tuned on “Faults

and digital outputs” tab.

NB : this function is reset 20 seconds after the
engine is stopped.

- [Expert mode] Enable/disable of Faults

Allows to activate/deactivate the regulator

protections (overvoltage, over-excitation,..).

- [Expert mode] Grid Code Function

Allows to activate/deactivate this function.

At least one CT is necessary to use this

function. It allows to switch from PF

regulation mode to voltage regulation mode

when the voltage is out of the range -90%

and 110% of the rated voltage.

- [Expert mode] Nominal excitation

current

This value comes from the database but can

be changed by the user. This value must be

set according to the admissible excitation

current for the generator.

- [Expert mode] digital input/ outputs

It is possible to reverse these digital IOs.

- [Expert mode] Digital external setting

memorization

This function is use in « +/-» mode; it allows

to keep the regulation mode adjustment in

case of DC supply cut off.

3.3.4 - [Expert mode] D510C Options

The regulator D510C offers several

functions accessible by clicking on the

button:

- [Expert mode] rotating diode bridge

fault

Activate/deactivate the rotating diodes state

supervision of exciter.

In case of the supervision of activation of

this feature, the « shutdown Iexc » function

must be also enabled.

- [Expert mode] Generator current

limitation

Set this function.

- [Expert mode] CAN network

configuration

Enable CAN.

Set the data transfer rate.

Choose the regulator identifier.

Select the broadcast protocol (J1939 and/or

Owner CAN).

In the case of Owner CAN, choose the

parameters to broadcast.

kVAR convention:

when generator

convention is selected then the kVAR is

considered negative when generator is

consuming reactive power and vice versa.

Содержание Leroy-Somer D510 C

































































Результаты поиска

Содержание Leroy-Somer D510 C

Отзывы:

Бренды по названию

Популярные бренды

Nidec Leroy-Somer D510 C, Руководство по установке и обслуживанию

Результаты поиска

Содержание Leroy-Somer D510 C

Отзывы:

Бренды по названию

Популярные бренды