English –
23
“Move anyway” function
If some safety device is not working or is faulty, it is possible to control and move the gate anyway in “Hold-to-run” mode. For further details,
please refer to the tearout insert “USER GUIDE” (final part of the manual).
9
DIAGNOSTICS
Some devices are display messages to identify their status and faults.
9.1 - Control unit signals
The leds on the control unit issue signals to indicate their normal/faulty operation.
Table 13 lists the signals:
Table 13
OK LED
Cause
Solution
Red and green
leds OFF
Serious
Check if the power is on; check fuses have not been tripped: if that is the case, check
the cause of the fault and replace with others of the same value.
Red or green
led ON
Serious
malfunction
Try and switch the control unit off for a few seconds; if the situation does not
change, there is a fault and the electronic board must be replaced.
1 green flash a
second
All OK
Normal operation of the control unit.
1 red flash
1 sec. pause
1 red flash
the installation of the devices was
not successful or the configuration
of the 1-2 dip switches was changed
without re-learning the devices
Check the correct connection of the alt and photocell inputs (see figure 7 and
paragraphs 8.1.1 and 8.1.2) or if the configuration of micro switches 1-2 has been
changed, perform the device learning procedure (paragraph 5.2)
2 quick green
flashes
There has been a change
in the input status
This is normal when there is a change in one of the inputs: SbS,
STOP, triggering of photocells or the radio transmitter is used.
2 red flashes
1 sec. pause
2 red flashes
Triggering of a photocell
At the beginning of the manoeuvre, one or more photocells are preventing movement:
check to see if there are any obstacles.
During the closing movement it is normal if an obstacle is really present.
4 red flashes
1 sec. pause
4 red flashes
Activation of the STOP input
At the start of the manoeuvre or during the movement, the STOP input has been
triggered:
check the cause.
5 red flashes
1 sec. pause
5 red flashes
Internal parameter memorisation
error
Wait at least 30 seconds during which the control unit tries to reset. If the situation
does not change,
it is necessary to delete the memory and carry out the storing procedure again
7 red flashes
1 sec. pause
7 red flashes
- Error in the internal circuits.
- configuration of programming
switches 1 and 2 changed
Disconnect all the power circuits for a few seconds, then try again and send
a command; if the situation does not change there may be a serious fault on the
board or on the motor wiring: check and replace as required.
If the configuration of switches 1 and 2 has been modified, repeat the device learning
procedure or reset the previous configuration
8 red flashes
1 sec. pause
8 red flashes
Command already present.
Another command is already present. Remove the command to be able to send
more.
PHOTO led
Cause
Solution
Off
Photocell input activated
At the start of the manoeuvre, one or more photocells are preventing movement;
check to see if there are any obstacles, also check the NC connection for faults.
On
All OK
The photocell is aligned and the movement is permitted
STOP led
Cause
Solution
Off
Activation of the STOP input
Check the devices connected to the STOP input
On
All OK
STOP Input active
SbS led
Cause
Solution
Off
Step-by-step command not present
On
Step-by-step command present
FCA led
Cause
Solution
Off
FCA limit switch input triggered
On
FCA limit switch input closed
FCC led
Cause
Solution
Off
FCC limit switch input triggered
On
FCC limit switch input closed
RADIO led R
Cause
Solution
Off
During normal operation, it shows a radio code that is not in the memory has been received.
On
Radio transmitter programming or deletion in progress
Содержание ROBO600
