background image

16

R

EV

1.02

1 6 / 0 8 / 1 8

Nice Australia Home Automation Pty Ltd Warranty Terms

a.

Nice Australia warrants that, goods manufactured by it, bearing the

GDS

brand, shall be free from defect in

manufacture for a period of 12 months from the date of invoice.  Should any fault occur within that period,
as a result, of faulty workmanship or materials, Nice Australia will at its discretion, replace the product at
no charge to the Customer except for removal, installation & freight.  The appropriate Serial Number must
be quoted for all warranty claims and a Nice warranty form filled out and returned with the item.

b.

For the goods not manufactured by Nice Australia, we shall pass on the manufacturer’s warranty to the
customer from the date of invoice.  It is the manufacturer’s discretion to repair or replace goods deemed to
be defective, as a result of faulty workmanship or materials.

c.

All goods must be returned to Nice Australia or its representative for inspection or testing to assess if a
claim is justified.  It is the responsibility and at the cost of the Customer, to remove & return the goods for
inspection and freight costs are the responsibility of the Customer.

d.

The warranty is negated and will not apply in the following circumstances:

i. If no proof of date of purchase can be produced.

ii. If the product has been used in a manner beyond its design parameters.

iii. If the product is tampered with or repaired by personnel not authorised to do so.
iv. In respect of loss or damage caused by rough treatment.

v. If the product is not used and maintained in accordance with instructions or recommendations listed

in this Installation and Maintenance Manual.

vi. In respect of loss or damage caused by an Act of God or any other cause not within the

manufacturers control.

e.

Goods returned under warranty for repair or testing will incur a charge to be fixed by the manufacturer if
no fault is found.

f.

The Customer shall bear freight charges for removing & returning the goods for inspection and for the
delivery & installation of any replacement or repaired product from a justified warranty claim.

g.

Save for the express conditions and warranties herein contained all other conditions or warranties
(whether as the quality, fitness for purpose or any other matter) expressed or implied by statute, common
law, equity, trade custom, usage or otherwise are hereby expressly excluded provided that nothing in these
terms and conditions shall exclude or limit any breach or condition implied by law, the exclusion or
limitation of which is not permitted by law.

Содержание GDS 450LI

















Отзывы: