background image

29

Nice Group USA Limited Warranty – 2 (TWO) YEARS 

Nice Group USA (“Manufacturer”) warrants this product shall be free from defects in materials and 
workmanship for a period of 2 years from the manufacture date. These warranties are in lieu of all other 
warranties expressed or implied and shall be considered void if the product is damaged due to, but 
not limited to, improper installation, improper use, terrorism or acts of God. The proper operation of 
this product is dependent on your compliance with the instructions regarding installation, operation, 
maintenance, and testing. Failure to comply strictly with those instructions will void this limited warranty in 
its entirety. 

If, during the 2 year time period from the date of manufacture,

 

this product appears to contain a defect 

covered by this limited warranty, 

call the manufacturer service center at 1-800-226-0178 

before 

uninstalling and/or dismantling this product. The technical assistance department at the manufacturer 
will discuss the problems you are experiencing in order to confirm the product defect. You will provide 
the information from the dated proof of purchase receipt to confirm the warranty period or the technician 
will confirm your extended warranty period through your registration information on file. The technician 
will give you the shipping information you need to return your product. Your product must be returned to 
the manufacturer service center in a prepaid and insured manner. Should your product be covered under 
the warranty policy, your product will be repaired, replaced with a factory rebuilt product or replaced with 
a new product (at the manufacturer’s discretion) at no cost to you and sent back to you via standard 
ground freight. 

THIS WARRANTY AND THE OBLIGATIONS AND LIABILITIES OF MANUFACTURER ARE 
EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING 
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR 
PURPOSE.

 Under no circumstances shall the manufacturer be liable for consequential, 

incidental or special damages of any kind whatsoever. The manufacturer’s liability for a breach 
of warranty, breach of contract, negligence or strict liability cannot exceed the cost of the 
warrantied product. No person is authorized to assume for the manufacturer any other liability 
in connection with the sale of this product.

 

31 - WARRANTY

Содержание 72001K

































Отзывы: