Nexo GEO M10 Скачать руководство пользователя страница 29

Страница: 29 / 79

GEO

M10

HARDWARE SETUP PROCEDURE

Page 29/79

GEO M10 Right

Set the bumper on the ground so that front is

on the “A” hole side

Remove the two BL820 quick release pins from their side storage position, and the BL825 quick
release pin of rear LBUMPM10 link bar.

Release GEO M10 link bar.

Position first GEO M10 on top of the bumper, and lock it to the bumper with the 2 BL820 quick release
pins.

Connect the bumper link bar (selection of -3° / 0° / +3°) to GEO M10 rear rigging plate (hole marked
“bumper”) Lock with the quick release pin BL0825.

Subsequent GEO M10s

Position second GEO M10 cabinet with AutoRig

in automatic lock position, and lock front points to

first GEO M10

Unlock GEO M10 link bar

Pull the latch to engage the guide in GEO M10 rear slot.

Adjust the angle by inserting quick release pin BL820 in proper hole.

Connect subsequent GEO M10 cabinets as with second.

IMPORTANT

Ensure that bumper quick release pins are properly locked into GEO M10, and that all

AutoRig

and rear pins are locked

Содержание GEO M10
















































































Результаты поиска

Содержание GEO M10

Отзывы:

Похожие инструкции для GEO M10

Бренды по названию

Популярные бренды

Nexo GEO M10, Руководство по установке

Результаты поиска

Содержание GEO M10

Отзывы:

Похожие инструкции для GEO M10

Бренды по названию

Популярные бренды