Nexo GEO M10 Скачать руководство пользователя страница 47

Страница: 47 / 79

GEO

M10

HARDWARE SETUP PROCEDURE

Page 47/79

Please check NS1 for mechanical Safety Working Load and acoustic computations.

IMPORTANT

Motor hoist must be rated to support entire cluster weight. Please check configuration

in NS1 for proper motor hoist rating

Procedure

GEO M10 Left

Position first GEO M10 so that Autorig

is at the bottom

Pull the bumper front latches, rotate the lower links so that connection points are double leg and
release the latches.

Position bumper on top of first GEO M10 and lock front points to the bumper with 2 BL820 quick
release pins.

Connect the bumper link bar (0° / “S" position) to GEO M10 rear rigging plate (hole marked “bumper”)
Lock with the quick release pin BL0825.

GEO M10 Right

Position first GEO M10 so that Autorig

is at the top and set in automatic lock position

Pull the bumper front latches, rotate the lower links so that connection points are single leg and
release the latches.

Position bumper on top of first GEO M10, front points will lock automatically

Connect the bumper link bar (0° / “S" position) to GEO M10 rear rigging plate (hole marked “bumper”).
Lock with the quick release pin BL0825.

If flying with bumper only, pull front and rear center latches, and release front and rear bumper
connecting points.

Subsequent GEO M10s

If required, position VNT-EXBARM10 frontwards or rearwards into VNT-BUMPM10 slots and lock
devices with the quick release pins 12x40 stored on VNT-BUMPM10.

Содержание GEO M10
















































































Результаты поиска

Содержание GEO M10

Отзывы:

Похожие инструкции для GEO M10

Бренды по названию

Популярные бренды

Nexo GEO M10, Руководство по установке

Результаты поиска

Содержание GEO M10

Отзывы:

Похожие инструкции для GEO M10

Бренды по названию

Популярные бренды