Nexo GEO M10 Скачать руководство пользователя страница 34

Страница: 34 / 79

Page 34/79

GEO

M10

HARDWARE SETUP PROCEDURE

6.3.4 MSUB15 and GEO M10 with Ministack adaptor

Ministack

adaptor only allows to stack GEO M10 in “left” configuration

Required item

1 x VNT-MNSTKM10

IMPORTANT

Ground stack assembly is rated for a maximum of 2 x 3 x GEO M10 in any inter
cabinet angle configuration with +/-12° initial angle, provided this device is assembled
according to below rules:

MSUB15 must always be installed on a horizontal surface

Public is not allowed within a safety area which radius is equal or higher than
assembly height.

Procedure

Position first MSUB15 on the ground

Position second MSUB15 (front or back) on top of first, and lock front and rear connecting points

Insert MNSTKM10 back into MSUB15 rear upper slot, and push it forward so that front opening are
aligned with MSUB15 front connecting points.

Unlock upper MSUB15 connecting points

Pull the latch to unlock the link bar

Содержание GEO M10
















































































Результаты поиска

Содержание GEO M10

Отзывы:

Бренды по названию

Популярные бренды

Nexo GEO M10, Руководство по установке

Результаты поиска

Содержание GEO M10

Отзывы:

Бренды по названию

Популярные бренды