Nexans EUROMOLD K800PB/G Скачать руководство пользователя страница 8

Страница: 8 / 14

In case the tee connector has been already installed

(otherwise proceed to step no. 6).

cable

clamp

earthing

lead

copper wire

screen

clamping

screw

basic

insulating

plug

Separable tee connector

protective

cap

Remove the protective cap from the tee connector. Put the

protective cap aside in a clean and safe place for later re-use.

Remove the basic insulating plug. Use a wrench with 22 mm

socket. Put the insulating plug aside in a clean and safe place

for later re-use.

Type 1

: remove the clamping screw. Use a wrench with a

22 mm socket and an extension. Put the clamping screw

aside in a clean and safe place for later re-use.

Type 2

: remove the flange nut. Use a wrench with a 22 mm

socket and an extension. Put the flange nut aside in a clean

and safe place for later re-use.Check that M16 stud is still

mounted correctly.

Re-tighten to 30 Nm if required.

Proceed with step 10

on page 10.

Disconnect the earthing lead, copper wire screen and cable

clamps.

Disconnect the tee connector from the bushing.

The bushing should be free.

basic

insulating

plug

protective

cap

Type 1

Type 2

COUPLING CONNECTOR INSTALLATION ON TEE CONNECTOR

M16

flange nut

Page 8 of 14

IS97180-ENG - K800PB/G

-CW45-

CA0 - Revision 2

For

information

only

Содержание EUROMOLD K800PB/G















Результаты поиска

Содержание EUROMOLD K800PB/G

Отзывы:

Похожие инструкции для EUROMOLD K800PB/G

Бренды по названию

Популярные бренды

Nexans EUROMOLD K800PB/G, Руководство по установке

Результаты поиска

Содержание EUROMOLD K800PB/G

Отзывы:

Похожие инструкции для EUROMOLD K800PB/G

Бренды по названию

Популярные бренды