Nexans EUROMOLD K800PB/G Скачать руководство пользователя страница 5

Страница: 5 / 14

* USE ONLY THE SILICONE LUBRICANT SUPPLIED

Lubricate* the indicated area: core insulation, semi-conductive screen, water sealing mastic and inner surface of the

reducer.

Slide the reducer down the cable until flush with the tape marker.

Remove the protective adhesive tape from the conductor.

INSTALLATION OF THE CABLE REDUCER

For conductor sizes 16 up to 150 mm²

core insulation

cable reducer

remove

protective

adhesive tape

lubricate

tape marker

Slide the installation rod on to the conductor until it butts against the core insulation.

Thoroughly clean installation rod and core insulation.

Always wipe towards the screen wires.

Lubricate* the indicated area: installation rod, core insulation, semi-conductive screen, water sealing mastic and

inner surface of the reducer.

Slide the reducer on to the installation rod.

Slide the reducer down the cable until flush with the tape marker. Take care to slide the reducer without hesitation

and in one smooth move.

Remove installation rod and protective adhesive tape from the conductor.

core

insulation

installation

rod

installation

rod

core insulation

lubricate

cable reducer

lubricate

tape marker

For conductor sizes 185 mm² up to 300 mm²

cable reducer

remove

protective

adhesive tape

Page 5 of 14

IS97180-ENG - K800PB/G

-CW45-

CA0 - Revision 2

For

information

only

Содержание EUROMOLD K800PB/G















Результаты поиска

Содержание EUROMOLD K800PB/G

Отзывы:

Похожие инструкции для EUROMOLD K800PB/G

Бренды по названию

Популярные бренды

Nexans EUROMOLD K800PB/G, Руководство по установке

Результаты поиска

Содержание EUROMOLD K800PB/G

Отзывы:

Похожие инструкции для EUROMOLD K800PB/G

Бренды по названию

Популярные бренды