Nexans EUROMOLD K800PB/G Скачать руководство пользователя страница 7

Страница: 7 / 14

* USE ONLY THE SILICONE LUBRICANT SUPPLIED

COUPLING CONNECTOR INSTALLATION ON CABLE

coupling

connector

housing

lubricate

Clean cable reducer, core insulation and contact.

Lubricate* the inside of the connector housing and outer surface of the

cable reducer.

Check if the

outer cone interface is pointed towards the

bushing.

Whilst preventing the cable reducer from

further movement down the cable gently slide the housing on the cable.

Its final position is reached when the centre

of the contact spade is along the axis of the interfaces of the connector.

The cable reducer must stay in place during installation.

Make sure the contact spade locks into the connector's housing.

Check that the ridge on the cable adapter is sitting at

5-25

mm below the connector housing.

holding tool

contact

palm

equipment

bushing

For aluminium conductors : before installing the conductor contact, wire brush the conductor.

Insert, if necessary, the centre ring into the contact barrel according to the table in the contact installation

instruction.

Position the contact so that the contact hole aligns with the bushing hole.

Tighten the contact. Please refer to the installation instruction included with the contact.

It is recommended to use a holding tool for ease of installation.

After tightening, distance

« Z »

must be between

145

and

165

mm.

If necessary, adjust the position of the cable reducer until distance

« Z »

is within the tolerance range.

cable reducer

Before tightening

After tightening

conductor

contact

Z = 145 - 165

clean

5-25

ridge on

cable reducer

Mechanical type contacts (Type TMBC-X)

Page 7 of 14

IS97180-ENG - K800PB/G

-CW45-

CA0 - Revision 2

For

information

only

Содержание EUROMOLD K800PB/G















Результаты поиска

Содержание EUROMOLD K800PB/G

Отзывы:

Похожие инструкции для EUROMOLD K800PB/G

Бренды по названию

Популярные бренды

Nexans EUROMOLD K800PB/G, Руководство по установке

Результаты поиска

Содержание EUROMOLD K800PB/G

Отзывы:

Похожие инструкции для EUROMOLD K800PB/G

Бренды по названию

Популярные бренды