Nexans EUROMOLD K800PB/G Скачать руководство пользователя страница 11

Страница: 11 / 14

coupling

connector

Clean and lubricate* both female tee connector interface and male interface of the coupling connector.

Push the coupling connector on to the contact rod of the tee connector. Take care not to damage the contact rod

during installation of the coupling connector.

22 mm

socket

1/2" - 12,7 mm

torque wrench

L ≥ 130 mm

extension

coupling

connector

22mm

* USE ONLY THE SILICONE LUBRICANT SUPPLIED

50 Nm

contact

rod

equipment

bushing

lubricate

equipment

bushing

clamping

screw

Insert the clamping screw into the threaded hole of the contact rod

by hand.

Use torque wrench with extension and a 22 mm socket and tighten exerting

Nm (5 kgm or 36,9 foot-pounds) of

torque.

In order to achieve the correct applied torque ensure that there is no lubricant on the threaded

parts.

Proceed with installing the basic insulation plug on page 13.

Type 1: clamping screw

Page 11 of 14

IS97180-ENG - K800PB/G

-CW45-

CA0 - Revision 2

For

information

only

Содержание EUROMOLD K800PB/G















Результаты поиска

Содержание EUROMOLD K800PB/G

Отзывы:

Похожие инструкции для EUROMOLD K800PB/G

Бренды по названию

Популярные бренды

Nexans EUROMOLD K800PB/G, Руководство по установке

Результаты поиска

Содержание EUROMOLD K800PB/G

Отзывы:

Похожие инструкции для EUROMOLD K800PB/G

Бренды по названию

Популярные бренды