Nexa Dago red Unlimited Air Racer 4 Скачать руководство пользователя страница 14

Страница: 14 / 20

Using a aluminum motor mounting plate
as a template, mark the plywood motor
mounting plate where the four holes are
to be drilled.

Remove the aluminum motor mounting
plate and drill a 3mm hole through
the plywood at each of the four marks
marked .

3mm

Step 16:1

Using a wooden motor mounting plate
as a template, mark the fire-wall where
the four holes are to be drilled.

! Align the mark on wooden motor
mounting plate with the mark on
the fire-wall.

Fuselage - Front-view

Step 16:2

Step 16:3

To muffler

Filler tube

To engine

Rubber stopper

Checking for leaks - block the vents and blow into the feed.
if in doubt submersing the tank in a blow of water will show
up any problems.

Blow

Water

Carefully install the fuel tank to ensure that they will not
shift during flight (secure the fuel tank in place using foam padding).

P-51 Voodoo

15- Fuel tank

16- Electric motor

Содержание Dago red Unlimited Air Racer 4





















Результаты поиска

Содержание Dago red Unlimited Air Racer 4

Отзывы:

Похожие инструкции для Dago red Unlimited Air Racer 4

Бренды по названию

Популярные бренды

Nexa Dago red Unlimited Air Racer 4, Инструкция по эксплуатации

Результаты поиска

Содержание Dago red Unlimited Air Racer 4

Отзывы:

Похожие инструкции для Dago red Unlimited Air Racer 4

Бренды по названию

Популярные бренды