Nexa Dago red Unlimited Air Racer 4 Скачать руководство пользователя страница 2

Страница: 2 / 20

1.5mm

A B

L/R

Assemble left and right
sides the same way.

Drill holes using the stated

size of drill
(in this case 1.5 mm Ø)

Use epoxy glue

Take particular care here

Hatched-in areas:

remove covering
film carefully

Not included.
These parts must be

purchased separately

Check during assembly that these

parts move freely, without binding

Apply cyano glue

The pre-covered film on ARF kit may wrinkle due to variations
of temperature. Smooth out as explained right.
* Use an iron or heat gun. Start as low setting. Increase the
setting if necsessary. If it is too high, you may damage the
film

Low setting

SILICON

EPOXY A

EPOXY B

GLUE

Epoxy Glue ( 5 minute type)

Silicon sealer

Cyanoacrylate
Glue

Epoxy Glue (30 minute type)

TOLLS REQUIRED

Hobby knife

Needle nose Pliers

Phillip screw driver

Awl

Scissors

Wire Cutters

(Purchase separately)

Hex Wrench

.........................................................

Sander

Masking tape - Straight Edged Ruler - Pen or pencil - Rubbing alcohol - Drill and Assorted Drill Bits

Read through the manual before you begin, so you will have an overall idea of what to do.

Symbols used throughout this instruction manual, comprise:

(Purchase separately)

CONVERSION TABLE

1.0mm = 3/64”
1.5mm = 1/16”
2.0mm = 5/64”
2.5mm = 3/32”

3.0mm = 1/8”
4.0mm = 5/32”
5.0mm = 13/64”
6.0mm = 15/64”

10mm = 13/32”
12mm = 15/32”
15mm = 19/32”
20mm = 51/64”

25mm = 1”
30mm = 1-3/16”
45mm = 1-51/64”

Minimum 7 channel radio
for airplane with 7 servos

.60 ~.70 - 4 cycle

10.5x6 for .40 - 2 cycle engine
11x6 for .46 - 2 cycle engine
12x6 for .60 - 4 cycle engine
12x7 for .70 - 4 cycle engine
13x8 for G-46 HP Motor.

Silicone tube

Extension for aileron
servo, retract servo.

.46 ~ .50 - 2 cycle

REQUIRED FOR OPERATION (Purchase separately)

.Motor control x1
.Elevator x1
.Rudder x1
.Aileron x2 mini servo
.Flap x2 mini servo

600-700Watt
Brushless motor

Motor Control

Li-Po Battery, 5 cell 4500mAh.

Содержание Dago red Unlimited Air Racer 4





















Результаты поиска

Содержание Dago red Unlimited Air Racer 4

Отзывы:

Похожие инструкции для Dago red Unlimited Air Racer 4

Бренды по названию

Популярные бренды

Nexa Dago red Unlimited Air Racer 4, Инструкция по эксплуатации

Результаты поиска

Содержание Dago red Unlimited Air Racer 4

Отзывы:

Похожие инструкции для Dago red Unlimited Air Racer 4

Бренды по названию

Популярные бренды