background image

Introduction

Astra2Connect Point&Play

®

 Setup Manual - page 4

Version 2.3 - January 2009

Safety precautions

This section lists the safety precautions to follow when installing the antenna.

Safety precautions are grouped into warnings and cautions.

Local regulations

Always install the Astra2Connect antenna in accordance with applicable local regulations. Consult 

with a licensed electrician if in any doubt.

Warnings

warning

 refers to an action or situation that could result in 

injury, long term 

health hazard or death

 if you do not follow the instructions.

Antenna

- RF radiation hazard: Hazardous electromagnetic field levels are generated in the area 

between the antenna reflector and the iLNB feed horn during transmission. Do not 

place any part of your body in that zone while the system is on. Take the necessary 

precautions to prevent access to the antenna by children or unauthorised persons.

IPmodem

- There are no user-serviceable parts in the IPmodem. Do not attempt to open the system. There 

is a risk of electrical shock that may result in injury and death. The IPmodem should only be 

opened by a technician trained and certified to service the product.

- To prevent the risk of fire or electrical shock, do not expose the indoor equipment to 

rain, liquids or moisture. Do not place any objects containing liquids (e.g. glasses, 

vases) on the system.

- Do not install the antenna and IPmodem when there is a risk of thunderstorm or lightning 

activity in the area.

- Do not use the in-line power supply power cord when damaged in any way.

Содержание Astra2Connect













































Отзывы: