Section 55 - Electrical System, Controller - Chapter 6
55-6-61
STEP 15
RD06A128
The display will return to the AUX SETUP screen.
Use the INCR or DECR key to go to the next menu
item.
Aux Cal Menu
Requirements For Calibration
IMPORTANT: The remote hydraulic controller must
be calibrated anytime any service work is done on
the remote valves or when the controller is changed.
•
Before starting the remote hydraulic calibration
p r o c e d u r e , c h e ck t h e w i r i n g h a r n e s s a n d
components for damage or loose connections.
R e p l a c e o r r e p a i r a n y d a m a g e d p a r t a s
necessary.
•
Before calibrating the remote hydraulic controller,
be sure the Standard Instrumentation (INST) and
Armrest (ARM) controllers are calibrated.
•
The hydraulic oil must be warmed to 49°C (120°F)
or higher.
•
Engine speed must be set to 1500 RPM or higher.
•
Disconnect any implements before calibration.
Calibration Process
Before the calibration process starts, the system will
perform a pre-calibration check. This check includes:
:
•
Levers and switches for the available valve
sections are in the neutral position.
•
W h e n e q u i p p e d w i t h M e g a F l o w, p l u g t h e
transducer into the left diagnostic fitting on the
remote manifold.
•
There are no faults present.
•
The feedback signal used for the calibration
indicates less than 100 PSI (689 kPa) and is
greater than 0.25 volts.
If any of these checks do not pass, the calibration will
be exited with a message displayed of the fault.
Selection of the INCR or DECR key will bring the
main calibration menu back.
If the checks pass, the present calibration values are
set to a default value and the calibration process will
begin.
The sequence of calibration is sequential from valve
section one through section five of the available
sections. The valve order for each section is lower
first, then raise. The valve and section that is in
process of calibration will be displayed.
If Equipped with MegaFlow
For tractors equipped with the MegaFlow option, a
pause is provided to allow field technicians to
calibrate both remote systems with one pressure
transducer.
Once the calibration procedure is in progress for the
1st remote section, move the 3rd remote lever out of
neutral. The calibration will pause after the 2nd
remote section is calibrated. Move the transducer to
the right side diagnostic fitting. Place the 3rd remote
lever back into neutral and select continue from the
menu. The calibration process will continue.
The valve is commanded to starting current. After
three seconds, the pressure reading is verified that it
has not changed more than 27 PSI (186 kPa) higher.
If the feedback signal is above this, calibration will be
stopped. If the value is below this pressure check,
the pressure reading is stored for the initial value and
used for a relative reference for the remainder of this
valve calibration.
Ever y 200 mS, the commanded current will be
incremented until the feedback signal has become
greater than 27 PSI (186 kPa) from the initial value
recorded. The valve is then commanded to zero
current and allowed to settle for three seconds. The
feedback is then checked for a value below 18 PSI
(124 kPa) from the initial value. A minimum of one
second and up to 30 seconds is allowed for this
signal to decay. The valve is then commanded at the
current just found minus 16 mA. The current is
incremented every three seconds until a change of
27 PSI (186 kPa) or greater from the initial value is
reached. Again the valve is allowed to settle as
above. If the feedback signal does not decay within
the time frame allowed, the calibration will exit.
When calibration is completed, the thresholds will be
saved and Done will be displayed on the standard
instrumentation display. If calibration is stopped, one
of the following messages will be displayed:
Содержание T8010
