New Holland 716523006 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 20

New Holland 716523006 Скачать руководство пользователя страница 4

4

Setup

Note:

Determine the left and right sides of the machine from the normal operating position.

Loose Parts

Note:

Use the chart below to identify parts used for assembly.

Description

Qty.

Use

Mower belt

1

Route the mower belt.

Pulley box
PTO drive belt

1
1

Install the mower.

Routing the Mower Belt

Route the mower belt as shown in Fig. 2. Ensure that you

install the belt on the lower mower deck pulley.

2

1

m--3524

Figure 2

Top View

1. Mower belt

2. Mower deck pulley

Installing the Mower

Preparing the Tractor

Install the mower on a level concrete surface. Rougher dirt

or lawn surfaces make installation more difficult.

1.

Position the tractor and mower side by side, with the

mower on the right side of the tractor.

2.

Set the parking brake, raise the attachment lift, stop the

engine, and remove the ignition key.

3.

If you have previously had a snowthrower, blade, or

tiller attached to the attachment lift, remove the two

clevis pins on each side of the attachment lift (Fig. 3).

2

1

m--3433

Figure 3

1. Clevis pin

2. Hairpin cotter

4.

Attach the pulley box if it is not already on the tractor

(Fig. 4).

«
...
2
3
4
5
6
...
»

Содержание 716523006





















Отзывы:

Нет отзывов