manualshive.com logo in svg

New Holland 716523006, Руководство оператора, Страница: 17 / 20

Поделиться
Скачать
New Holland 716523006 Скачать руководство пользователя страница 17

17

Troubleshooting

Problem

Possible Causes

Corrective Action

Abnormal vibration.

1. A blade is bent or unbalanced.

1. Install new blades.

2. A blade mounting bolt is loose.

2. Tighten the blade mounting

bolts.

3. The engine mounting bolts are

loose.

3. Tighten the engine mounting

bolts.

4. A loose engine pulley, idler

pulley, or blade pulley.

4. Tighten the appropriate pulley.

5. The engine pulley is damaged.

5. Contact your Authorized

Service Dealer.

Blades do not rotate.

1. The blade drive belt is worn,

loose, or broken.

1. Install a new blade drive belt.

2. The blade drive belt is off the

pulley.

2. Install the blade drive belt and

check idler pulley and belt

guides for correct position.

3. The PTO belt is worn, loose, or

broken.

3. Install a new PTO belt.

Uneven cutting height.

1. The tire pressure is incorrect.

1. Set tire pressure.

g

g

2. The mower is not level.

2. Level the mower from

side-to-side and front-to-rear.

3. The underside of the mower is

dirty.

3. Clean the underside of the

mower.

Insufficient transport height.

1. The lift arm cams are

improperly adjusted.

1. Adjust lift arm cams.

Содержание 716523006





















Отзывы:

Нет отзывов