New Holland 715648006 Скачать руководство пользователя страница 12

12

Grease the Channel Pivot

1. Lower the attachment.

2. Set the parking brake, stop the engine, and remove the

ignition key.

3. Clean the area around the channel pivot with a rag.

Apply grease to the pivot bolt, frame and sector 
(Fig. 24).

m–1473

Figure 24

4. Wipe off excess grease.

Oil Linkages

1. Set the parking brake, stop the engine, and remove the

ignition key.

2. Place a few drops of oil on all movable linkages 

(Fig. 24).

3. Wipe off excess oil.

Reversing the Scraper Blade

The scraper blade contacts the ground, preventing damage
to the snow blade.  Periodically inspect the scraper blade
for wear.  When the scraper becomes worn, before the
working surface contacts the housing, reverse the scraper
blade.

1. Start the tractor, raise the blade, and support the

housing off the ground.

2. Set the parking brake, stop the engine, and remove the

ignition key.

3. Remove the lock nuts and carriage bolts securing the

scraper (Fig. 25).

4. Reverse the scraper blade to replace a worn edge and

install it with the previously removed hardware
(Fig. 25).

m–1468

1

2

3

Figure 25

1.

Lock nut

2.

Carriage bolt

3.

Scraper blade

Storage

1. Before long-term storage, wash the machine with mild

detergent and water to remove dirt and grime from the
entire machine.

2. Check the condition of the scraper blade; refer to

Reversing the Scraper Blade, page 12.

3. Grease and oil the blade; refer to Greasing and

Lubrication, page 11.

4. Check and tighten all bolts, nuts, and screws.  Repair

or replace any part that is damaged.

5. Paint all scratched or bare metal surfaces.  Paint is

available from your Authorized Service Dealer.

6. Store the machine in a clean, dry garage or storage

area.

7. Cover the machine to protect it and keep it clean.

Содержание 715648006

















Отзывы: