27
Control Room section) to the selected Speaker Outputs
via the Main Volume control.
suM - Is a latching function, and allows multiple Monitor
Sources to be selected. When SUM is selected again, the
Monitor Source will revert to the last selected source.
reTrO OP - Routes the Main Mix (post Master Fader)
through the main Retro Mix stage (LO1166) to the Main
Output & the Control Room section.
MDrn OP - Routes the Main Mix (post Master Fader)
through the main Modern Mix stage (transformerless) to
the Main Output & the Control Room section.
MOn MIX - Routes the Monitor Mix to the Main Output &
the Control Room section.
auX 1, auX 2, auX 3 and auX a, auX B buttons route
the respective send to the selected Speaker Outputs via
the Master Aux control and the Main Volume control.
Control room
Headphones
The Control Room Headphone Output (HP) is located
directly above the Main Volume Control. The level control
adjacent to it effects the output level of the headphone
and the PFL bus.
CrM HP - Feeds the currently selected Monitor Source to
the Control Room Headphones.
HP1 - Routes Headphone Output 1 to the Control Room
Headphones.
HP2 - Routes Headphone Output 2 to the Control Room
Headphones.
PFl - Feeds the PFL bus to the Control Room
Headphones.
solo
The following buttons effect soloing globally. There
are four global Solo Modes available on the Series 75
console. After-Fader Listen, Pre-Fader Listen, Solo In
Place, and Solo In Front. LEDs in the Solo Modes section
light to display which of the four modes are active at any
one time. All buttons other than Solo Clear are recallable.
sOlO Clear - Clears all active Solos on the console.
sOlO MODe - Cycles through the four Solo Modes.
After-Fader Listen (aFl), Pre-Fader Listen (PFl), Solo In
Place (sIP), and Solo In Front (sIF).
»
aFl - A Solo button will send an After Fader
Listen signal from the soloed Channel or Monitor
path to the AFL bus and on to the Speaker
Outputs. The AFL bus is stereo, and soloing
is non-destructive (solo does not affect the
Channel Direct Output or Main Mix Out signals).
»
PFl - A Pre-Fader Listen signal will be
sent from the soloed Channel or Monitor
path to the PFL bus and on to the Speaker
Outputs. The PFL bus is mono, and soloing
is non-destructive. The PFL Level Control is
directly above the Control Room Volume.
»
sIP - A Solo button will simply cut all other
signals which have neither their solo isolate
mode activated, or been soloed themselves.
Soloing is destructive (Channel Direct
Outputs and Mix Outputs are Cut).
»
sIF - An After Fader Listen signal will be sent
from the selected Channel or Monitor path to
the AFL bus and on to the Speaker Outputs.
The Main Mix is padded 10dB and added to
the AFL bus. Soloing is non-destructive.
lInK - Links the Channel path and Monitor path Solos.
When selected, soloing any signal (Channel or Monitor
Path) will result in all other un-soloed channels being
cut. If unselected, Channel path and Monitor path Solos
operate independently.
Talkback and listen Mic
The built-in TalKBaCK microphone is accessed here.
Talkback can be fed to the Auxiliary Sends, Cues, two
Headphone Outputs, and Studio Loudspeakers. When
Talkback is activated, DIM is automatically engaged.
»
auX - Feeds Talkback to Auxiliary
Outputs 1, 2, 3, A and B.
»
HP1 & HP2 - Feeds Talkback to
Headphone Send 1 or 2 via the
respective Headphone Send Level.
»
Cue - Routes Talkback to both Headphone
Sends 1 & 2 via their level controls.
»
sls - Routes Talkback to the Studio
Loudspeakers via the SLS Level Control.
The lIsTen MIC is an extra input designed for a
dedicated studio to control room communication
microphone (dynamic only). The rotary control labeled
lIsTen MIC sets the level of this input. The button
labeled lIsTen, situated directly below, sends the signal
to the Speaker Outputs cutting the currently selected
Monitor Source.
sTaTus lOCK - Locks out the CONSOLE MODE
buttons, CHANNEL MODE buttons (other than PAN),
OSC to GRPS/MAIN MIX, and the SIP SOLO MODE.
