NetLink 700-883-PRO42 Скачать руководство пользователя

Страница: 43 / 68

NETLink

Switch

After the new parameterization data have been stored, the NET-
Link

Switch is restarted to activate the new configuration.

Parameters of the TCP access list:

TCP access list
ON/OFF

Switch ON/OFF the functionality of the TCP ac-
cess list.

TCP/IP address
1 and 2

First and second IP addresses that are allowed to
access the NETLink

Switch.

TCP/IP address
3 and 4

Third and fourth IP addresses that are allowed to
access the NETLink

Switch.

TCP/IP address
5 and 6

Fifth and sixth IP addresses that are allowed to
access the NETLink

Switch.

TCP/IP address
7 and 8

Seventh and eighth IP addresses that are allowed
to access the NETLink

Switch.

TCP/IP address
9 and 10

Ninth and tenth IP addresses that are allowed to
access the NETLink

Switch.

TCP/IP address
11 and 12

Eleventh and twelfth IP that are allowed to access
the NETLink

Switch.

SPS write Protection

PLC write-protection ON or OFF

NETLink

Switch can be started both locally and remotely via the

security interface. This is done by clicking the ‘

Device Reboot

’ but-

ton.

7.5

Observing variables

In addition to the “

Observing Variables

” function in the Simatic

engineering tools, NETLink

Switch also provides this function via

the web interface.

Setting parameters of the observe variables function:

MPI address

An active MPI/PB address is selected using the
dropdown menu.

Number of Variables

The number of variables to be observed can be
selected from 1 to 10 for a clearer view.

No.

Consecutive numbering.

Address Area

The following viewable items are supported: OB,
OW, OD, IB, IW, ID, MB, MW, MD, DBB, DBW,
DBD, counter, and timer.

Address Index*

Address of the bytes to be displayed. * On the
case of data blocks with the form
“Datablock.Offset”

Result Value

If one of the buttons is pressed, the output value
will be displayed here

Display Format

Display formats: decimal, hexadecimal, or binary

Description

Freely selectable description (max. 32 chars)

Rebooting can take up to
15 seconds.

Содержание 700-883-PRO42





































































Результаты поиска

Содержание 700-883-PRO42

Отзывы:

Похожие инструкции для 700-883-PRO42

Бренды по названию

Популярные бренды

NetLink 700-883-PRO42, Руководство пользователя

Результаты поиска

Содержание 700-883-PRO42

Отзывы:

Похожие инструкции для 700-883-PRO42

Бренды по названию

Популярные бренды