manualshive.com logo in svg

NetLink 700-883-PRO42, Руководство пользователя

Поделиться
Скачать
NetLink 700-883-PRO42 Скачать руководство пользователя страница 11

 

NETLink

®

 Switch 

 

11

3

 

System Overview 

3.1

 

Application and function description 

NETLink

®

 Switch is a gateway between a TCP network and a MPI, 

PPI, or PROFIBUS network. 

Two protocols are available at the TCP end for exchange of useful 
data with the automation system (multi-protocol operation): 

•

 

One is a proprietary protocol that is used to connect to the pro-
prietary NETLink-S7-NET driver 

•

 

The other is the S7-TCP/IP protocol often used by visualization 
system manufacturers which is known as 

‘RFC1006’

 or 

‘ISO on 

top of TCP’

. 

Up to 16 TCP connections (10 Mbps or 100 Mbps) and up to 32 
MPI/PPI/PROFIBUS connections (9.6 kbps to 12 Mbps) can be used 
simultaneously. 

The integrated 4-way switch makes it possible to connect further 
Ethernet nodes to NETLink

®

 Switch. If NETLink

®

 Switch has to be 

restarted via the driver or the web interface (e.g., due to new con-
figurations), the Switch stays ready for use without a new initializa-
tion of the 4 ports.  

On both the TCP and the field bus sides, the baud rate used can be 
determined automatically (auto negotiation or autobaud). 

NETLink

®

 Switch needs to get 24 VDC power via the power sup-

plies at the lower left side of the case. 

The connecting cable used to link NETLink

®

 Switch with the pro-

grammable controller is to be connected to the front of NETLink

®

 

Switch. In case of a branch line it is to be executed actively (acces-
sories, see chapter 3.5). When a node is integrated in the bus, the 
connection can be carried out via a common PROFIBUS plug (ac-
cessories, see chapter 3.5). 

The use of the NETLink-S7-NET driver makes it possible to use 
NETLink

®

 Switch as the following at the PC end 

•

 

Programming adapter, 

•

 

Teleservice unit, or 

•

 

Operator control and monitoring unit and 

•

 

Ethernet switch 

The RFC1006 interface also enables you to use third-party software 
that supports this protocol to communicate with S7-200/S7-300 
and S7-400 systems. 

NETLink

®

 Switch can generally be connected to the PC via switch, 

hub or directly via LAN cable in both cases. 

Содержание 700-883-PRO42





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды