NetLink 700-883-PRO42 Скачать руководство пользователя

Страница: 23 / 68

NETLink

Switch

5.1.3

PPI configuration

Basically, the same applies to PPI configuration as to MPI configu-
ration. However, the network-related parameters are more exten-
sive.

In addition to the parameters transmission rate and highest sta-
tion address mentioned in Section 5.1.1, PROFIBUS also has a pa-
rameter field for selecting the bus profile and bus parameters:

According to current knowledge, all S7-200 CPUs of the product
line 22x should be able to communicate with ‘

Advanced PPI.

’ It is

recommended to use ‘

Advanced PPI

’ if possible.

5.2

Local connection (TCP parameterization)

There are three basic ways of parameterizing NETLink

Switch at

the TCP end:

•

Parameterization via ‘Set

PG/PC interface

Existing stations can be reparameterized using the ‘

Change

’

button

•

Parameterization via the ‘

NETLink PRO Family configuration

’

tool (see Section 6).

•

Parameterization via the web interface of the NETLink

Switch

(see Section

7.3

If the NETLink

Switch is configured via the NETLink-S7-NET

driver, the following points must be considered:

If the NETLink

Switch is active on the bus when reparameteriza-

tion is required (e.g. a variable table or block is being viewed),
reparameterization is not performed.

Normally the baud rate
cannot be detected auto-
matically at PPI systems.

Содержание 700-883-PRO42





































































Результаты поиска

Содержание 700-883-PRO42

Отзывы:

Похожие инструкции для 700-883-PRO42

Бренды по названию

Популярные бренды

NetLink 700-883-PRO42, Руководство пользователя

Результаты поиска

Содержание 700-883-PRO42

Отзывы:

Похожие инструкции для 700-883-PRO42

Бренды по названию

Популярные бренды