NetLink 700-883-PRO42 Скачать руководство пользователя

Страница: 10 / 68

NETLink

Switch

Installation and Mounting

Installation and mounting must be effected in compliance with
VDE 0100 / IEC 364. Because it is an IP20 module, you must install
it in a cabinet.

A maximum ambient temperature of 60 ºC must be ensured for re-
liable operation.

2.1

Mounting orientation

NETLink

Switch can be installed in any position.

2.2

Minimum clearance

Minimum clearances must be observed because

•

Then it is possible to insert and remove NETLink

Switch with-

out having to remove other system components.

•

There is enough space to connect existing interfaces and other
contacts using standard commercial type accessories.

For NETLink

Switch, a minimum clearance of 30 mm should be

left above and below and 10 mm at the sides.

2.3

Installing the module

NETLink

Switch is intended to be mounted on a DIN rail bracket.

It can be snapped into place by simply attaching it to the DIN rail
bracket. In order to do so, you hook NETLink

Switch into the rail

bracket at the upper groove of the DIN rail bracket and push NET-
Link

Switch in direction of the rail bracket. Thereupon, NETLink

Switch should snap into place automatically. In order to remove
the hardware module from the rail bracket, it is necessary to push
NETLink

Switch up first and then remove it from the upper

groove.

Before you start installa-
tion work, all system
components must be
disconnected from their
power source.

Содержание 700-883-PRO42





































































Результаты поиска

Содержание 700-883-PRO42

Отзывы:

Похожие инструкции для 700-883-PRO42

Бренды по названию

Популярные бренды

NetLink 700-883-PRO42, Руководство пользователя

Результаты поиска

Содержание 700-883-PRO42

Отзывы:

Похожие инструкции для 700-883-PRO42

Бренды по названию

Популярные бренды