NETGEAR Nighthawk X4S R7800 Скачать руководство пользователя страница 10

Страница: 10 / 160

Table 1. LED and button descriptions

Description

LED

•

Solid amber. The router is starting.

•

Blinking amber. The firmware is upgrading, or the Reset button was pressed.

•

Solid white. The router is ready.

•

Blinking white. The firmware is corrupted.

•

Off. Power is not supplied to the router.

Power

•

Solid white. The Internet connection is ready.

•

Solid amber. The router detected an Ethernet cable connection to the modem.

•

Off. No Ethernet cable is connected between the router and the modem.

Internet

•

Solid white. The 2.4 GHz WiFi radio is operating.

•

Blinking. The router is sending or receiving WiFi traffic.

•

Off. The 2.4 GHz WiFi radio is off.

2.4 GHz WiFi

•

Solid white. The 5 GHz WiFi radio is operating.

•

Blinking. The router is sending or receiving WiFi traffic.

•

Off. The 5 GHz WiFi radio is off.

5 GHz WiFi

•

Solid white. A USB device is connected and is ready.

•

Blinking. A USB device is plugged in and is trying to connect.

•

Off. No USB device is connected, or someone clicked the Safely Remove Hardware button and it
is now safe to remove the attached USB device.

USB 3.0 port 1 and USB
3.0 port 2

•

Solid white. An eSATA device is connected and is ready.

•

Blinking. An eSATA device is plugged in and is trying to connect.

•

Off. No eSATA device is connected.

eSATA

Hardware Setup

Nighthawk X4S AC2600 Smart WiFi Router

Содержание Nighthawk X4S R7800

































































































































































Результаты поиска

Содержание Nighthawk X4S R7800

Отзывы:

Похожие инструкции для Nighthawk X4S R7800

Бренды по названию

Популярные бренды

NETGEAR Nighthawk X4S R7800, Руководство пользователя

Результаты поиска

Содержание Nighthawk X4S R7800

Отзывы:

Похожие инструкции для Nighthawk X4S R7800

Бренды по названию

Популярные бренды