manualshive.com logo in svg

NetApp FAS9500, Руководство пользователя

Поделиться
Скачать
NetApp FAS9500 Скачать руководство пользователя страница 31

A3

B3

1

DCPM module terra cotta locking button

3. Set the DCPM module aside in a safe place and repeat this step for the remaining DCPM module.

Step 6: Replace a chassis from within the equipment rack or system cabinet

You must remove the existing chassis from the equipment rack or system cabinet before
you can install the replacement chassis.

1. Remove the screws from the chassis mount points.

If the system is in a system cabinet, you might need to remove the rear tie-down bracket.

2. With the help of two or three people, slide the old chassis off the rack rails in a system cabinet or 

L

brackets in an equipment rack, and then set it aside.

3. If you are not already grounded, properly ground yourself.

4. Using two or three people, install the replacement chassis into the equipment rack or system cabinet by

guiding the chassis onto the rack rails in a system cabinet or 

L

 brackets in an equipment rack.

5. Slide the chassis all the way into the equipment rack or system cabinet.

6. Secure the front of the chassis to the equipment rack or system cabinet, using the screws you removed

from the old chassis.

7. Secure the rear of the chassis to the equipment rack or system cabinet.

8. If you are using the cable management brackets, remove them from the old chassis, and then install them

on the replacement chassis.

9. If you have not already done so, install the bezel.

Step 7: Move the USB LED module to the new chassis

Once the new chassis is installed into the rack or cabinet, you must move the USB LED
module from the old chassis to the new chassis.

Animation - Remove/install USB module

29

Содержание FAS9500





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды