Neousys Technology POC-551VTC Series Скачать руководство пользователя страница 3

Страница: 3 / 113

Table of Content

3.2.5

mSATA Module Installation

............................................................................... 55

3.3

M.2 (2242/ 3042) Module Installation

....................................................................... 56

3.4

Installing the System Enclosure

............................................................................. 59

3.5

Wall Mount Installation

............................................................................................ 61

3.5.1

Vertical Wall Mount Bracket (Optional)

.............................................................. 62

3.6

DIN Rail Installation (Optional)

................................................................................ 63

3.7

Powering On the System

......................................................................................... 66

3.7.1

Powering On Using the Power Button

............................................................... 66

3.7.2

Powering On Using An External Non-Latched Switch

....................................... 67

3.7.3

Powering On Using Wake-on-LAN

.................................................................... 68

3.8

Ignition Power Control

............................................................................................. 71

3.8.1

Principles of Ignition Power Control

.................................................................. 71

3.8.2

Additional Features of Ignition Power Control

................................................... 72

3.8.3

Wiring Ignition Signal

........................................................................................ 73

3.8.4

Configure your Windows system

....................................................................... 74

3.8.5

Operation Modes of Ignition Power Control

...................................................... 75

BIOS Settings

4.1

COM1/ 2 Port Configuration

.................................................................................... 78

4.2

COM 3/ 4 Port Configuration

................................................................................... 79

4.3

COM Port High Speed Mode

.................................................................................... 80

4.4

SATA Configuration for MezIO

Module

................................................................ 81

4.5

TPM Availability

........................................................................................................ 82

4.6

System Power Configuration

.................................................................................. 83

4.7

Ignition Power Control

............................................................................................. 84

4.8

Power over Ethernet (PoE)

...................................................................................... 85

4.9

Wake-on-LAN

............................................................................................................ 86

4.10

Power On after Power Failure

........................................................................ 87

4.11

Boot Menu

................................................................................................................. 88

4.12

Boot Type (Legacy/ UEFI)

............................................................................... 90

4.13

Position New Boot Device

.............................................................................. 91

4.14

Watchdog Timer

.............................................................................................. 92

OS Support and Driver Installation

5.1

Operating System Compatibility

............................................................................. 93

5.2

Driver Installation

..................................................................................................... 94

5.2.1

Install Drivers Automatically

.............................................................................. 94

5.2.2

Install Drivers Manually

..................................................................................... 95

5.3

Driver for Watchdog Timer and DIO

........................................................................ 96

Appendix A Using WDT & DIO

WDT and DIO Library Installation

....................................................................................... 98

WDT Function Reference

.................................................................................................. 100

InitWDT

................................................................................................................................ 100

SetWDT

............................................................................................................................... 100

StartWDT

............................................................................................................................. 101

ResetWDT

........................................................................................................................... 101

StopWDT

............................................................................................................................. 101

Using DIO Function (POC516/ POC-546 Only)

................................................................. 102

Wiring for DIO

...................................................................................................................... 102

DIO Pin Definition

................................................................................................................. 103

DIO Function Reference

.................................................................................................... 104

InitDIO

.................................................................................................................................. 104

DIReadLine

.......................................................................................................................... 104

DIReadPort

.......................................................................................................................... 104

DOWriteLine

......................................................................................................................... 105

DOWritePort

......................................................................................................................... 105

DOWriteLineChecked

.......................................................................................................... 106

DOWritePortChecked

........................................................................................................... 106

COS Function Reference

................................................................................................... 107

Содержание POC-551VTC Series


















































































































Результаты поиска

Содержание POC-551VTC Series

Отзывы:

Бренды по названию

Популярные бренды

Neousys Technology POC-551VTC Series, Руководство пользователя

Результаты поиска

Содержание POC-551VTC Series

Отзывы:

Бренды по названию

Популярные бренды