Neousys Technology POC-551VTC Series Скачать руководство пользователя страница 77

Страница: 77 / 113

POC-551VTC

4 BIOS Settings

The system is shipped with factory-default BIOS settings optimized for best

performance and compatibility. In this section, we’ll illustrate some BIOS settings you

may need to set or change prior to operating system installation. Please always

make sure you understand the effect of change before you proceed with any

changes. If you are unsure of the function you are changing, it is recommended to

change one setting at a time to see its effect(s).

NOTE

Not all BIOS settings will be discussed in this section. If a particular setting/ function

you are after requires specific BIOS settings but is not discussed in this section,

please contact Neousys Technical Support staff.

Содержание POC-551VTC Series


















































































































Результаты поиска

Содержание POC-551VTC Series

Отзывы:

Бренды по названию

Популярные бренды

Neousys Technology POC-551VTC Series, Руководство пользователя

Результаты поиска

Содержание POC-551VTC Series

Отзывы:

Бренды по названию

Популярные бренды