Neousys Technology POC-551VTC Series Скачать руководство пользователя страница 90

Страница: 90 / 113

POC-551VTC

4.12 Boot Type (Legacy/ UEFI)

The system supports both Legacy and Unified Extensible Firmware Interface (UEFI)

boot modes. UEFI is a specification proposed by Intel to define a software interface

between operating system and platform firmware. Most modern operating systems,

such as Windows 10 and Linux support both Legacy and UEFI boot modes. The

Legacy boot mode uses MBR partition for disk and VBIOS for video initialization, the

UEFI boot mode uses GPT partition which supports greater than 2TB partition size

and GOP driver for faster video initialization.

NOTE

If you choose Legacy mode, you will not be able to create disk partitions greater than

2TB or use TPM 2.0 function.

To configure Boot Type:

When system boots up, press F2 to enter BIOS setup utility.

Go to

[Boot]>[Boot Type]

, press ENTER to bring up options, Dual Boot

(UEFI), Legacy Boot Type, UEFI Boot Type.

Highlight your selection and press ENTER.

Press F10 to “Exit Saving Changes”.

Содержание POC-551VTC Series


















































































































Результаты поиска

Содержание POC-551VTC Series

Отзывы:

Бренды по названию

Популярные бренды

Neousys Technology POC-551VTC Series, Руководство пользователя

Результаты поиска

Содержание POC-551VTC Series

Отзывы:

Бренды по названию

Популярные бренды