Neousys Technology Nuvo-2400 Series Скачать руководство пользователя

Страница: 52 / 81

Nuvo-2400

User’s Manual

Page 52 of 81

4.8.3 Power on Using an External Non-latched Switch

When using the ATX-mode on/off control, you need a non-latched switch. The external

non-latched switch acts exactly the same as the power button on the front panel. To power

on Nuvo-2400 using an external non-latched switch (ATX-mode), please follow the steps

listed below:

1. Prepare a non-latched switch with a 2-pin, 2.0mm pitch connector. Connect the

non-latched switch to the ATX pin and GND pin of the on-board wafer connector.

Figure 47: Connecting a latched switch to ATX mode pin

2. Push the non-latched switch and then system is on (the blue LED of power button on

the front panel is on at the same time). Push the non-latched switch when system is on

can turn off the system. If your operating system supports ATX power mode (i.e.

Microsoft Windows or Linux), push the power button causes a pre-defined system

behavior, such as shutdown or hibernation.

Содержание Nuvo-2400 Series


















































































Результаты поиска

Содержание Nuvo-2400 Series

Отзывы:

Похожие инструкции для Nuvo-2400 Series

Бренды по названию

Популярные бренды

Neousys Technology Nuvo-2400 Series, Руководство пользователя

Результаты поиска

Содержание Nuvo-2400 Series

Отзывы:

Похожие инструкции для Nuvo-2400 Series

Бренды по названию

Популярные бренды