NeoDen NeoDen10 Скачать руководство пользователя страница 15

Страница: 15 / 64

4. PCB Information Editing

In File List interface, select the file to edit,enter to PCB Information interface, as show in the figure:

First, set the track width,adjust the track width according to the actual PCB width(usually actual PCB width plus

1mm),click Width Set,follow the prompt window to check whether back to zero condition are met.After back to zero, the

track width will be adjusted.After placing the PCB on the track,gently push the PCB back and forth by hand to confirm that

the PCB has a small gap of about 1mm in the track, so that the PCB can pass smoothly.

Secondly,set PCB Forward Position(note:Mag Fixture mode does not need to set Forward Position),click Align,select the

Forward Position according to the image recognized by Mark camera,select the Alignment Method nozzle 1, click save and

back,Forward Position is recorded ans saved.

4.1 PCB Forward Setting

There are three ways in PCB Forward Setting---Mag Fixture,Tracks,Long Tracks

（

）

Mag fixture

Select tray to fix the board feeding mode, place the PCB to be installed in the proper position in the mounting area, and then
click "top plate control" to fix the PCB.

（

）

Tracks

Select the “Tracks”on PCB Feed Setting interface:

Содержание NeoDen10

































































Результаты поиска

Содержание NeoDen10

Отзывы:

Похожие инструкции для NeoDen10

Бренды по названию

Популярные бренды

NeoDen NeoDen10, Руководство пользователя

Результаты поиска

Содержание NeoDen10

Отзывы:

Похожие инструкции для NeoDen10

Бренды по названию

Популярные бренды