13. The heater must not be located immediately below a wall
socket.
14. Do not connect the fan heater using an on/off timer or other
equipment which can automatically switch the device on.
15. The heater must not be placed in rooms where flammable
liquids or gases are used or stored.
16. If an extension cord is used, it must be as short as possible and
always be fully extended.
17. Do not use this heater in the immediate surroundings of a bath,
a shower or a swimming pool.
18. If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
19. You must not connect other appliances to the same mains
socket as the fan heater.
20. Make sure heater is always under surveillance and keep
children and animals away from it;
21.
When you don’t use the appliance for a long time, unplug the
appliance. Don’t leave the heater for a considerable amount of
time when in use. Pull the plug straight out, never remove the
plug by pulling on the cord.
22. Keep the heater far from curtain or places where the air inlet can
easily be blocked.
23. Parts of the heater may exceed 200
℃
, contact with the heating
tube, reflector, or mental parts near the heating tube, may cause
severe burns . To avoid burns, do not let bare skin touch hot
surface.
24. Always allow heating element to cool at least 10 minutes before
touching the heating tube or adjacent part
25. In order to prevent possible electric shock or leakage current,
never use the appliance with wet hand or operate the appliance
when there is water on the power cord.
26. Do not dispose of electrical appliances as unsorted municipal
waste, use separate collection facilities. Contact your local
government for information regarding the collection systems
available. If electrical appliance are disposed of in landfills or
dumps, hazardous substances can leak into the groundwater
and get into the food chain, damaging your health and well-
being.
27. This appliance is not intended for use by persons (including
children) with reduces physical, sensory or mental capabilities
or lack of experience and knowledge unless they have been
given supervision or instruction concerning the use of the
appliance by a person responsible for their safety.
28. Children should be supervised to ensure that they do not play
with the appliance.
TECHNIACAL SPECIFICATIONS
Model
90-036
Waterproof class
IP 34
Voltage
230V ~
Required power
2000W
Current
8,7A
Required fuse
10A
Setting
2000W
Self-resetting thermostat
Tak
Heating area
2-3 m2
Max. lighting time
6000 h
Dimensions (mm)
500x500x2075
Weight (kg)
10,7-13,2
INTRODUCTION
The infrared heaters produce instant and comfortable heat like the
sun. These robust and weatherproof heaters are designed for
domestic and commercial heating applications within indoor and
outdoor areas.
INSTALLATION
1.This heater should be installed by a competent person, i.e. a
qualified electrician.
2.Always disconnected the heater from the electricity supply and
allow it to cool before installation.
3.This heater can be heat directly.
4.Keep the supply cord away from the body of the heater which will
get hot during use.
5.Do not place the heater on an inflammable surface.
6.Place on a flat, stable surface when used
7.Observe the minimum safe distance between the heater body and
the inflammable surfaces when used.
8.If the heater is to be used outside, a weatherproof outlet is
recommended.
1
Hex screw
M6x30 mm
3 pc.
2
Flat gasket piece
Ø25
3 pc.
3
Elastic medium
6xT1.0
3 pc.
4
Base pad
M8x15
5 pc.
5
screw
PM5x10 mm
2 pc.
6
Pressure panel
PA66
2 pc.
7
screw
PW4x20 mm
4 pc.
Locate the top, middle, and bottom parts of the tripod. These pipes
are threaded and must be twisted. Then mount the base as shown in
the diagram above. Install the heating element on a tripod by
connecting the electrical connector as shown in the figure below.
