background image

Model

 

1100NG

1100LPG

1150NG

1150LPG

Gas

Natural

Propane

Natural

Propane

Altitude (Ft.)*

0-4,500 feet*

0-4,500 feet*

Input Maximum (Btu/h)

28,000

28,000

30,000

30,000

Input Minimum (Btu/h)

13,000

13,000

16,000

16,000

Manifold Pressure (in w.c.)

3.5”

9.0”

4.0”

9.0”

Minimum Supply Pressure (in w.c.)

5.0

11.0

5.0

11.0

Maximum Supply Pressure (in w.c.)

10.0

14.0

10.0

14.0

Main Burner Injector Marking

850

300

850

360

Pilot Injector Marking

51

30

51

30

Min. Rate By-Pass Screw

185

125

195

135

H5

4004585-03

©2014, Miles Industries Ltd.

Gas Conversion Kit

1100NGK / PGK & 1150NGK / PGK

Installation Instructions

This appliance is certifi ed for use from 0–4500 feet. For 
altitudes above 4500 feet, see local codes.

Kit Contents

1 Pilot injector
1 Main burner elbow injector
1 Set of conversion labels
1 Minimum rate by-pass screw

Tools Required

•  Wrenches, to disconnect gas line
•  Phillips (+) screwdriver, to remove burner module
•  Small (jewelers size) fl at blade screwdriver, to set 

pressure

• Small fl at blade screwdriver, to release pressure tap 

on valve

•  Needle nose pliers, to remove by-pass screw
•  Hex (Allen) wrench, 4 mm or 5/32”, to remove pilot 

injector

•  Manometer, to set pressure when regulator is integral 

with valve

Specifi cations

Use with with 

Valor Models 1100/1150 Heaters ONLY

WARNING

This conversion kit shall be installed by 
a qualifi ed service agency in accordance 
with the manufacturer’s instructions and 
all applicable codes and requirements of 
the authority having jurisdiction. If the 
information in these instructions is not 
followed exactly, a fi re, explosion or pro-
duction of carbon monoxide may result 
causing property damage, personal injury 
or loss of life. The qualifi ed service agency 
is responsible for the proper installation of 
this kit. The installation is not proper and 
complete until the operation of the con-
verted appliance is checked as specifi ed in 
the manufacturer’s instructions supplied 
with the kit.

Use this manual in conjunction with the 
installation manual supplied with the 
appliance.

Содержание Valor H5 Series









Отзывы: