manualshive.com logo in svg

NEC UNIVERGE UM8500, Руководство по интеграции

"NEC UNIVERGE UM8500 - это мощная система управления, обеспечивающая безупречную коммуникацию в вашем офисе. Здесь вы можете скачать бесплатное руководство по эксплуатации, чтобы максимально эффективно использовать все функции этого продукта. Посетите наш сайт manualshive.com для загрузки."

Поделиться
Скачать
background image

UNIVERGE UM8500 I

NTEGRATION

 G

UIDE

 

68

Troubleshooting

If one of these problems listed below is encountered, try the corrective actions 
listed for the problem. If these actions do not correct the problem, or if the 
problem is not described here, contact Technical Support. 

Problems

Corrective actions

Calls to the voice messaging 
system do not connect. 
Calls to the voice messaging 
system connect, but no prompts 
play. 
Callers entering an extension are 
always answered with the opening 
greeting instead of the personal 
greeting. 
Calls are not integrating with the 
phone system. 
Easy message access is not 
functioning: subscribers access 
their voice mailboxes and hear the 
opening greeting instead of 
personal options.
Calls are forwarded to the opening 
greeting instead of a subscriber’s 
mailbox. 

Perform the following for the problems listed:

●

Confirm that expansion boards are firmly seated in the computer 
expansion slots and that each board is properly configured. See 
“Installing or reseating voice boards” in the appendix titled “Adding or 
changing the voice boards” in the

 Installation Guide

.

●

See the 

Installation Guide

 and check the voice board settings.

●

Confirm that the PBX station interface cables between the systems are 
connected and functioning correctly. Try testing each cable or replacing 
each with a different cable. 

●

Confirm that the correct phone system model is set up on the voice 
messaging system. On the UM8500 Administrator, go to 

Switch 

> 

Switch

 Information and check that the correct phone system 

manufacturer and model type are displayed. 

The voice messaging system takes 
a long time detecting disconnected 
calls.

Confirm that the Last Party Clear Dial option is set up on the phone system.

Callers are asked to hold or 
complain that they are on hold for 
too long when calling an extension 
that is using “Do not disturb” 
mode.

Typically this happens because the voice messaging system is set up to use 
the await-answer transfer type and call holding for that extension. Call holding 
must be turned off when using the “Do not disturb” mode on the phone.

The phone system cabinet that 
contains the voice messaging 
station cards sporadically resets 
itself.

The phone system might be overloaded due to an increase in polling traffic 
between the D82 boards and the system. Spread out the load by distributing 
the voice messaging extensions among multiple station cards on the phone 
system. For example, distribute three or fewer voice messaging extensions 
per station card. 

Subscriber’s phones are not 
forwarding calls on ring-no-answer 
or on busy.

Confirm that the subscriber’s phone is set up on the phone system to forward 
calls to the voice messaging hunt group pilot number on ring-no-answer and 
on busy. 

Subscribers are not being identified 
by the system, using identified 
subscriber messaging, when 
leaving messages for other 
subscribers.

Confirm that identified subscriber messaging is set up correctly on the voice 
messaging system. 

Subscriber message waiting 
indication fails.
Message waiting indicators are not 
activated after messages are left.
Message waiting indicators are not 
turned off after messages are 
retrieved.

Perform the following for the problems listed:

●

On the UM8500 Administrator, on the Ports page verify that at least one 
of the voice messaging ports is set for MWI dialout. 

●

On the UM8500 Administrator, confirm that MWI is enabled for the 
subscriber.

Await-answer calls release before 
the personal greeting is played.

See “

Learning phone system tones

”

 on page 340

.

Содержание UNIVERGE UM8500

































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для UNIVERGE UM8500

Samsung OfficeServ 7200 System Description preview
OfficeServ 7200
Бренд: Samsung Страницы: 137
Samsung SMT-W5100 Instruction Manual preview
SMT-W5100
Бренд: Samsung Страницы: 129
Bang & Olufsen BeoCom 1401 Manual preview
BeoCom 1401
Бренд: Bang & Olufsen Страницы: 2
Evolveo EasyPhone FP Manual preview
EasyPhone FP
Бренд: Evolveo Страницы: 27
Clas Ohlson 38-8610 User Manual preview
38-8610
Бренд: Clas Ohlson Страницы: 2
Trillium Panther II 2064 Technical & Service Manual preview
Panther II 2064
Бренд: Trillium Страницы: 108
ONE.TEL Magma 110 User Manual preview
Magma 110
Бренд: ONE.TEL Страницы: 47
CEECO HOB-331-F Service Manual preview
HOB-331-F
Бренд: CEECO Страницы: 15
Blackberry ASY-12747-002 - RIM HS-655+ Bluetooth Headset User Manual preview
ASY-12747-002 - RIM HS-655+ Bluetooth Headset
Бренд: Blackberry Страницы: 15
Uniden EXAI 3248 Series Owner'S Manual preview
EXAI 3248 Series
Бренд: Uniden Страницы: 68
Geemarc Amplidect 295 SOS-Pro Quick User Manual preview
Amplidect 295 SOS-Pro
Бренд: Geemarc Страницы: 2
Geemarc AMPLIVOICE50 User Manual preview
AMPLIVOICE50
Бренд: Geemarc Страницы: 31
Geemarc AmpliDECT 300 User Manual preview
AmpliDECT 300
Бренд: Geemarc Страницы: 58
Innovaphone IP64 Product Data preview
IP64
Бренд: Innovaphone Страницы: 31
Fulljoin FJ880 Quick Start preview
FJ880
Бренд: Fulljoin Страницы: 3
Jabra SP5050 - Bluetooth hands-free Speakerphone Manual preview
SP5050 - Bluetooth hands-free Speakerphone
Бренд: Jabra Страницы: 14
MobileVision BT-HFKP5 Operation And Installation Manual preview
BT-HFKP5
Бренд: MobileVision Страницы: 8
LG-Ericsson LDP-7008D User Manual preview
LDP-7008D
Бренд: LG-Ericsson Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды