NEC POWERMATE PRO2180 Скачать руководство пользователя страница 156

Страница: 156 / 211

Setting System Board Jumpers 6-7

CLEARING CMOS

If you want to return your system to the factory default
settings, use the following procedure to clear CMOS to the
default factory settings.

CAUTION:

Clearing CMOS changes your setup configuration
including hard disk settings.

Power off the system and unplug any peripherals.

WARNING

The system power must be off before removing the
cover and changing a jumper setting.

Remove the system unit cover (see “Removing the
System Unit Cover in Chapter 5).

Locate the CMOS Clear jumper on the system board
(see the figure “Locating system configuration
jumpers”).

You may have to remove any installed expansion
boards to access the jumpers (see “Removing
Expansion Boards” in Chapter 5).

Remove the jumper block from pins 20-22 and set it on
pins 18-20.

Содержание POWERMATE PRO2180




















































































































































































































Результаты поиска

Содержание POWERMATE PRO2180

Отзывы:

Похожие инструкции для POWERMATE PRO2180

Бренды по названию

Популярные бренды

NEC POWERMATE PRO2180, Руководство пользователя

Результаты поиска

Содержание POWERMATE PRO2180

Отзывы:

Похожие инструкции для POWERMATE PRO2180

Бренды по названию

Популярные бренды