NEC POWERMATE PRO2180 Скачать руководство пользователя страница 151

Страница: 151 / 211

6-2 Setting System Board Jumpers

CHANGING PROCESSOR JUMPER SETTINGS

The following procedure explains how to locate and change
the jumper setting when you upgrade your processor.

WARNING:

The system power must be off before changing a
jumper setting.

Power off and unplug the system and any peripherals.

Remove the system unit cover (see “Removing the
System Unit Cover” in Chapter 5).

Locate these jumpers on the system board (see the
following figure).

You may have to remove any installed expansion boards
to access the jumpers (see “Removing Expansion
Boards” in Chapter 5).

Содержание POWERMATE PRO2180




















































































































































































































Результаты поиска

Содержание POWERMATE PRO2180

Отзывы:

Похожие инструкции для POWERMATE PRO2180

Бренды по названию

Популярные бренды

NEC POWERMATE PRO2180, Руководство пользователя

Результаты поиска

Содержание POWERMATE PRO2180

Отзывы:

Похожие инструкции для POWERMATE PRO2180

Бренды по названию

Популярные бренды