NEC NVM-CA Series Скачать руководство пользователя | Manualshive

Страница: 69 / 266

background image

Mitel SX-50 (Inband)

Issue 1-0

Integration Notes

X

65

Mitel SX-50 (I nband )

Integrati on Notes

Required Hardware and Software

Q

Software requirements: Generic MS55-MR5-PR5-G07.11 or higher.ONS Line Card, part num-
ber 9104-020-002
Each Voice Mail port requires a port from this card.

Q

LS/GS Line Card, part number 9104-030-004
Each Voice Mail port requires a port from this card.

Voice Mail Availability

This phone system is available on these Voice Mail systems:

Q

NVM-22CA with software version 8.01 or higher

Q

NVM-202exCA with software version 7.01 or higher

Q

NVM-2000CA with software version 8.01 or higher

Phone System Programming

General Programming Information

Since the SX-50 uses “loop back trunks” when integrating with the Voice Mail, any incoming
call is “looped back” on a trunk into the Voice Mail, after the Voice Mail Master Extension
number is dialed.

The SX-50 uses Abbreviated Dialing and Automatic Route Selection for this type of
integration.

You will need the Mitel SX-50 Technical Practices to complete this programming.

Command 100 SYSTEMS OPTIONS PROGRAMMING

The following registers require entries that are different from the default values:

Register 05 TRUNK CONNECTIONS
Bit c: CO to CO Connections
Enter 1 to Enable this bit.

Register 09 FEATURES SELECTION 1
Bit h: Abbreviated Dial Access
Enter 1 for 3-digit index number (900 entries maximum)

Register 11 TIME OUT SELECTION
Bit g: Call Forward No Answer Timeout
Enter 2 for 20 seconds.

Register 12 MESSAGE WAITING
Bit c: Message Waiting System Enable
Enter 1 to Enable with Lamps
Bit d: Message Waiting Indication
Enter 0 for Always.
Bit f: Message Waiting Automatic Cancel
Enter 0 to Disable.

Register 13 AUTOMATIC ROUTE SELECTION (ARS)
Bit c:  ARS Enable
Enter 1 to Enable.
Bit f: ARS Return Dial Tone
Enter 1 to Enable.
Bit h: Attendant ARS Routing Class of Service
Enter 1 for RCS 1.
Bit i:  ARS Interdigit Timeout
Enter 0 for 5 seconds.
Bit j:  Abbreviated Dial ARS Bypass Enable
Enter 1 to Enable.

«
...
67
68
69
70
71
...
»

Содержание NVM-CA Series











































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NVM-CA Series

Бренд: Aastra Страницы: 91

Бренд: Aastra Страницы: 20

Бренд: AT&T Страницы: 116

FortiVoice 50E6

Бренд: Fortinet Страницы: 22

Бренд: GE Страницы: 46

Бренд: BT Страницы: 69

Бренд: Gigaset Страницы: 58

Бренд: XtendLan Страницы: 63

WRT-10-H Series

Бренд: C.J. ANDERSON Страницы: 8

EVITA Telephone

Бренд: Topcom Страницы: 8

Бренд: Kodak Страницы: 25

Бренд: Geemarc Страницы: 72

Бренд: Leviton Страницы: 2

Бренд: Sanyo Страницы: 30

Бренд: Sanyo Страницы: 45

Бренд: Sanyo Страницы: 53

Бренд: Sanyo Страницы: 10

Бренд: Sanyo Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды