NEC NVM-CA Series Скачать руководство пользователя

Страница: 85 / 266

ONYX I

Issue 1-0

Integration Notes

ONYX I

Integrati on Notes

The information below applies to the ONYX I 60x60 phone system.

Hardware and Software Requirements

Hardware:
ASI (Analog Station Interface) P/N 88188

Software:
Release 3.0 or higher (P/N 89749)

Voice Mail Availability

This phone system is available on the NVM-2000CAwith software version 8.01 or higher.

Phone System Programming

For Voice Mail Integration

Program 2

Use this program to set a station’s voice mailbox number.

Program 5

Use this program to set the Voice Mail wait timer.

Program 10

Use this program to set a Conversation Record key at a station.

Program 11

Use this program to set a station connected to a VX port.

For Automated Attendant

Program 3

Enter 2 for a VX Automated Attendant line.

System Options

Listed below are two types of Voice Mail options:

Ones that the ONYX I does not use (listed as “not used”)

Ones that may have default values not listed in the Programming Guide

RNA, Hold Retrieval String

Not used

Busy, Hold Retrieval String

Not used

Lamp On String

DEFAULT:

#XG

Lamp Off String

DEFAULT:

#X00

Transfer String

DEFAULT:

Содержание NVM-CA Series











































































































































































































































































Результаты поиска

Содержание NVM-CA Series

Отзывы:

Похожие инструкции для NVM-CA Series

Бренды по названию

Популярные бренды

NEC NVM-CA Series, Руководство по интеграции

Результаты поиска

Содержание NVM-CA Series

Отзывы:

Похожие инструкции для NVM-CA Series

Бренды по названию

Популярные бренды