NEC MultiSync FP1370 Скачать руководство пользователя страница 52

Страница: 52 / 286

5-23

4-10. Overall Distortion Adjustment

Signal: No. 33 (788*1200@75Hz) All white

1) Confirm that adjustment on steps 4-2 to 4-9 meets the specifications.

2) If undulating, re-adjustment each distortion adjustment.

Undulation is a directional difference of tilt at either AC and CE or both.

Following figures (I) and (II) are example. AB and BC, CD and DE are the direction of tilt.

Undulated correction is the same direction of tilt at AB and BC, CD and DE.

Following figures (III) and (IV) are example. In this state, each adjustment standard must be met.

( | )

( || )

( ||| )

( |V )

Fig 4-14 Undulated Definition

5. Preset Picture Size and Position Adjustment

Signal:

No. 3 (VGA480)

No.17 (1024*768@75Hz)

No. 6 (MAC 640*480)

No.21 (1280*1024@75Hz)

No.12 (VESA 640*480@85Hz)

No.22 (1600*1200@75Hz)

No.13 (MAC 832*624)

No.23 (1600*1200@85Hz)

No.14 (800*600@85Hz)

No.32 (1280*1024@85Hz)

Video:

All White

1) Receive signal 3.

2) Open Menu (S), TAG2 "H.POSITION", "V.POSITION", "H.SIZE", "V.SIZE".

3) Adjust the picture size and position as listed below by "+", "-" SW.

Picture size

H: 396

1.0 mm

V: 297

1.0 mm

Picture Position

H: | XL

eft

–

ight

1.0 mm

V: | XT

–

ottom

1.0 mm

4) Push "EXIT" SW.

5) Receive the next signal and repeat steps 2) - 4).

Note: Before receiving the next signal, always push "EXIT" SW to store adjustments.

XTop

XLeft

XRight

XBottom

Bezel

VIDEO

Fig 5-1 Picture Position

Содержание MultiSync FP1370































































































































































































































































































Результаты поиска

Содержание MultiSync FP1370

Отзывы:

Похожие инструкции для MultiSync FP1370

Бренды по названию

Популярные бренды

NEC MultiSync FP1370, Руководство по обслуживанию

Результаты поиска

Содержание MultiSync FP1370

Отзывы:

Похожие инструкции для MultiSync FP1370

Бренды по названию

Популярные бренды